A single phase transmission line is delivering 470 kVA load at 10 kV. Its resistance is 6.5 N and inductive reactance is 7 N if the load power factor is 0.8 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line

A single phase transmission line is delivering 470 kVA load at 10 kV. Its resistance is 6.5 N and inductive reactance is 7 N if the load power factor is 0.8 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)?
e) Alternating Current is preferred over Direct Current in Power System, Why? f) Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. g) Why the Capacitance effect is neglected in Short Transmission Line. h) Distinguish between Lumped or Distributed elements in a Transmission Line.
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?
A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10Megawatts at 0.8 power factor lagging, 30kV at the receiving end. If the minimum transmission line efficiency is to be limited to 96%, estimate the per phase values of resistance and inductance of the line.
Analyze the impact of distributed energy resources (DERs) and smart grid technologies on the modernization of power systems.
A balanced load of 30MW is supplied at 132 kV, 50Hz and 0.85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20+j 52) ohms and the total phase-neutral admittance is 315 micro mho. Shunt leakage may be neglected. Using the nominal T and π approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in the voltage at the receiving end.
A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0•85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admittance is 315 microsiemens. Shunt leakage may be neglected. Using the nominal T approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
1)Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. 2) Why the Capacitance effect is neglected in Short Transmission Line. 3) Distinguish between Lumped or Distributed elements in a Transmission Line.
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
The area of an interconnected power system has two units operating on economic dispatch. The variable operating costs of these units are given by C =8P +0.009P2 11 1(R/h) and C = 10P + 0.008P2 where P1 and P2 are in MW. The transmission losses for the area are given by ? = 1.5 × 10−4?2 + 2 × 10−5? ? + 3 × 10−5?2 , MW ?1122 2 2 2 (R/h,) Determine the following when the area λ = 16.00 R/MWh: a. The output of each unit b. Total transmission losses c. Total load demand d. Total operating cost
A 46-kv 0.8-lagging power factor load is connected to the end of a short transmission line where the voltage is 230. If the line resistance and reactance are 0.06 and 0.08 ohm, respectively, calculate the voltage at the sending end.
For the given 3-phase power transfer, a star system is associated with a greater insulation. Select one: True False