A single phase transmission line is delivering 460 kVA load at 11 kV. Its resistance is 4.5 Q and inductive reactance is 6 Q. If the load power factor is 0.7 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line

A single phase transmission line is delivering 460 kVA load at 11 kV. Its resistance is 4.5 Q and inductive reactance is 6 Q. If the load power factor is 0.7 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Similar questions

A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line
470 kVA load at 12 kV. Its resistance is 7 Ω and inductive reactance is 7 Ω if the load power factor is 0.9 lagging. Determine the Current through the line , Sending end voltage , Sending end power factor , Regulation of transmission line , Efficiency of transmission line Note:please do not handwriting
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
(Q) A 10 mile transmission line with an impedance of (0.122+j0.849) Ω per mile is delivering 230A at 230kV and 0.8 power factor lagging. Determine: the sending end voltage the line efficiency and regulation
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.
Using a test equipment, Vmax was found to be 5V while Vmin is 1V. The distance between voltage maximas is 14 cm and the first maximum was found to be 7 cm from the load. What is the load impedance if the characteristic impedance of the line is 75 ohms?
A 60 Hz, three-phase transmission line is 100 miles long. It has a total seriesimpedance of {35 + j120) n and a shunt admittance of j930 μsiemen. It delivers40 MW at 220 kV with 90% lagging power factor. Find the voltage at the sendingend by:(a) short line approximation(b) the nominal rr approximation(c) the nominal T approximationAlso determine the voltage regulation for the given line and the power loss.Assume the sending end voltage remains constant. Expected Answer: (a) 237.67 kV, 1.4284 MW, 8.03%; (b) 225.8 kV, 1.1642 MW, 8.67% (c) 225.10 kV, 1.5095 MW, 8.35% Pls. Provide Full Solution for thumbs up
A 69-kV, three phase short transmission line is 16km long. The line has a per phase series impedance of 0.125 + j0.4375 ohms per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers:(a) 70 MVA, 0.8 lagging power factor at 64 kV.(b) 120 MW, unity power factor at 64kV.
For a given short transmission line of impedance R+jX ohms/phase, the sendingend and receiving end voltages Vs and Vr are fixed. Derive the expression for themaximum power that can be transmitted over the line.