Answered: A turbine of 9000 B.H.P. is working…

A turbine of 9000 B.H.P. is working under a head of 25 m and runs at 100 R.P.M.- What will be the type of turbine ? What should be its speed and power, when it is working under a head of 16 m?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Related questions

Q: 3- The following rod rotates about AB axis. If the angular velocity and acceleration are…

Q: Q2/ The six cylinder of a single- acting, two-stroke cycle Diesel engine are pitched 1 m apart and…

Q: One mole of CO₂ is mixed with 3.5 moles of air which is composed of (79% N₂ and 21% O₂) as…

A: Given data The mixture consists of 1 mole of CO2 3.5 moles of air (79% N2 and 21% O2)

Q: A stone is dropped from a deck above a lake strikes the water after 9 seconds. Use acceleration due…

Q: For the shown figure, find the height (h)? Air 1.5 bar oil 0.8 4.5 m L S.G= 13.6 C Air water 3.2 bar…

Q: 4. A plate of 270 mm wide and 25 mm thick from carbon steel. A two-high rolling mill is used to…

Q: The following creep data were taken on an aluminum alloy at 480 C (900 F) and a constant stress of…

A: Enter the given values in Excel: To find: (a) Steady-state or minimum creep rate. (b) time of…

Q: A one ton car is initially travelling at 10 kph when it combusts 50 grams of fuel with calorific…

Q: A sab Later, one thickness is maint oined at surfaces is in veched to. increased to 50°C. 20°C…

A: Given : To find : Temperature distribution

Q: Determine the force in members ab,dh,dg, eg, hi,hj, & hk of truss shown h 6m in figure? 6 m 3m g 560…

Q: 20 kN/m 6m Determine reactions in A and tension in cable as shown in figure? 300 kN 30 kN/m B 8 m…

Q: 4. Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is…

A: Answer: Pulley 1 Pulley 2 Pulley 3 Angular Velocity 16.67 rad/s -25 rad/s 50 rad/s…

Q: Design the network represents the following activities, then 1) Calculate TE, .². 2) Find the…

A: Given

Q: Fig. and the magnitude of the resultant force FR if FR is directed along the positive x axis. 200 N…

Q: 4.15 The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30…

Q: Find pressure the pistoni

A: Given data; Piston diameter,d=30 cm Force,F=3000NFind pressure on the piston ?

Q: What is truss

A: This question is based on the concept of trust in mechanical engineering.

Q: This landing instrument guides a pilot to maintain a center position relative to the runway during…

A: given; landing instrument guide the pilot to maintain a center position relative to the runway…

Q: Label the following diagram of a fluid dispensing system using the provided labels Volume Request…

A: Introduction: Fluid dispensing system/equipments: Any machine that distributes, mixes and…

Q: 3. During the rolling process, the average flow stress is 20,000 lb/in², determining the amount of…

A: Given: The flow stress in material, σf = 20,000 lf/in^2 The strain hardening exponent, n = 0.4 The…

Q: For propylene plot the residual enthalpy and residual entropy functions over the reduced pressure…

A: Given that, Interpolation formulay-y1=y2-y1x2-x1x-x1y1=0.6 1→Propaney2=0.4…

Q: 1. A simply supported beam of span 3 m has the T-section shown in Figure 1 and carries a uniformly…

Q: wo bodies of masses (m₁ = 7 kg) and (m₂ = 5 kg) are connected by a light string passing over a…

Q: 100 mm 50 mm 150 mm An orifice with a 50 mm in diameter opening is used to measure the mass flow…

Q: A single disc clutch has 30 cm outside diameter and 22.5 cm inside diameter. Which of the following…

A: Given data Outside Diameter = Do = 30 cm = 300 mmInside Diameter = Di = 22.5 cm = 225 mmAverage…

Q: To view the complete problem, hover over the blue information symbol. The horizontal and vertical…

Q: Suppose that the temperature of heated plate at outer edges as shown in figure below. Using…

Q: The first answer for this problem was incomplete and the answer was cut off so if anybody can…

A: In this problem, it is saying that first answer is incomplete. It means the total acceleration at…

Q: An SUV hauling a trailer is travelling at 25 m/s when the driver hits the brakes. The 1.4 MT trailer…

A: Given : m1=1.4MT=1400 kgm2=1.6 MT=1600 kgF1=4500 NF2=5500 NV=25 m/s To find : what is the braking…

Q: What is the velocity as measured by an orifice plate (0.06-m diameter) in a 0.305-m-diameter pipe…

Q: The weight of the stationary box is 39.6 kg. The spring has a length of 0.18 m, an unstretched…

A: Given Angle = 20o Mass, m =…

Q: Knowing that the tensor has been adjusted so that the tension in the frame AD is 850 N, determine…

Q: 4. In Figure S6.4, four particles of masses 1kg, 2kg, 3kg and 4kg are at the vertices of a rhombus…

A: Given: a=2m and b=2m Because angle of b from the horizontal is not given: So we can assume that…

Q: A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm…

A: We know that a cylinder is made up of an outer tube with internal and external diameters of 16 cm…

Q: In case of negative work the angle between the force and displacement is O 45° O 180° O 90° O 0°

Q: What are the reaction forces?

A: we have to determine the reaction forces

Q: Determine maximum torque for the shaft?

A: Given data; Bending moment= 4.0 kNmTwisting moment= 6.0 kNmDetermine torque for the shaft ?

Q: The second law of thermodynamics implies that the coefficient of performance of a refrigerator must…

Q: What is the mass, in ounce mass, of the object below? Hint: A and B are parallels respectively.…

A: We have to calculate the mass for the given body. The material is aluminum

Q: Determine the load in members AC a 16 m C B 100 kg 8m

Q: 5. A cylindrical pressure vessel has an inner diameter of 240mm and a wall thickness of 1.5mm. If…

Q: The value of x,y and z are measured with maximum percentage error of 1%, 2% and 3%, respectively.…

A: Given that, w=5x6z3y The maximum percentage error in x is, δxx×100=1 In y is, δyy×100=2 In z is,…

Q: Label the following diagram of a fluid dispensing system using the provided labels • Volume Request…

A: Introduction: Fluid dispensing system equipmens: Fluid dispensing equipment includes any machine…

Q: Example 1 The bar is subjected to a moment of M = 17.5 N.m. If r = 5 mm, determine the maximum…

A: Introduction: Bending stress is the typical stress that an item experiences when subjected to a…

Q: The motor unit A is used to elevate the 300-kg cylinder at a constant rate of 2 m/s. If the power…

Q: Find the reactions at supports. 10 KN A 2 m 20 kN-m Im 3 m 24 kN-m B 10 kN E Im 2 m F

Q: When a0, the spring on the firing mechanism is unstretched. The arm is pulled back such that 100 mm…

Q: The state of stress at a point in member is given by: 50 60 100 60 40 80 MPa 100 80 20 A torsion…

A: Write the given data. σxx=50τxy=60τxz=100τyx=60σyy=40τyz=80τzx=100τzy=80σzz=20 According to…

Q: As you are walking in the forest you look up just as a boulder becomes dislodged from the side of a…

A: Height of the boulder from the head, h= 200 ft Acceleration due to gravity, a= 32 ft/sec2 Initial…

Q: The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the…

Question

A turbine of 9000 B.H.P. is working under a head of 25 m
and runs at 100 R.P.M.- What will be the type of turbine ? What
should be its speed and power, when it is working under a head of
16 m?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
A Francis turbine is to be designed to produce 27 MW at a shaft speed of 90rev/minunder an effective head of 27.8 m. Assuming that the optimum hydraulic efficiency is 90percent and the runner tip speed to jet speed ratio is 0.75, determine:(1) the power specific speed;(2) the volume flow rate;(3) the impeller diameter and blade tip speed.
Why are Francis and Kaplan turbines generally consideredunsuitable for hydropower sites where the availablehead exceeds 1000 ft?
The design of a new dam reveals that a water head of 10 meter and water flow rate of 100 cubic meter per second (m3/s) can be supplied for electricity generation. What kind of turbines would you recommend for the electric power generation?
Give at least two reasons why turbines often have greater efficiencies than do pumps.
An axial flow turbine is operated at a pressure head of 24m and develops 24.2MW when rotating at 146 r/min. The tips of the blades are on a diameter of 4,72m and the hub diameter is 2,1m. If the hydraulic efficiency is 94% and the overall efficiency 88%, determine the inlet and exit angles of the blades at the mean radius. Assume free vortex flow towards the rotor and conditions for maximum power
The date for a certain installation are as follows Net Head = 454 m, BP = 57,200 bkw, n = 750 rpm, ηT = 90%. What type of turbine was used? A. Impulse turbine B. Kaplan turbine C. Propeller turbine D. Francis turbine
A turbine is used to extract energy from water at a discharge of 1.5 cfs. If turbine head is ℎ? = 9ft and turbine efficiency η = 75 %, determine the effective output power in HP (horsepower)
Using the specific rotation speed, what would be the best turbine option for a waterfallof 120m and a flow of 6m³/s, working with a 12-pole generator? And what would be the nqa for thissituation?ALTERNATIVESa) Francis Turbine Normal, nqa= 121.88.b) Kaplan turbine, nqa= 7312.89.c) Slow Francis Turbine, nqa=98.15.d) Deriaz Turbine, nqa= 290.5.e) Pelton turbine, nqa= 29.05.
A hydroelectric plant has 14 identical Francis turbines, a gross head of 245 m, and a volume flow rate of 11.5 m3 /s through each turbine. The water is at 25°C. The efficiencies are ?turbine = 95.9%, ?generator = 94.2%, and ?other = 95.6%, where ?other accounts for all other mechanical energy losses. Estimate the electrical power production from this plant in MW
In a Francis turbine, when 6N force is applied to the disc with a radius of 0.08m, the revolution rate is 2500 rpm, the water flow rate is 8 m3 / h, the inlet pressure is 12 mSS and the outlet pressure is 0 mSS. In this case, calculate. Francis turbine efficiency
Identify the main types of Hydro power turbines and the difference between them.