Answer 1.8 and 1.9 Question 1A single stage reciprocating compressor takes 1m³ of air per minute and 1.013 bar and 15°C anddelivers at 7 bar. Assuming Adiabatic law (n=1.35) and no clearance.Calculate:1.1. Mass flow rate (1.226 kg/min)1.2. Delivery Temperature (475.4 K)1.3. Indicated power (4.238 kW)This same compressor is now driven at 300 rpm, has a stroke to bore ratio of (1,5:1), it has amechanical efficiency for the compressor of 85% and motor transmission efficiency of 90%.Calculate:1.4. Volume per cycle (0.00333 m³/cycle)1.5. Cylinder bore diameter (141.4 mm)1.6. Power to the compressor (4.99 kW)1.7. Motor power needed (5.54 kW)1.8. The isothermal power (3.265 kW)1.9. The isothermal efficiency (77%)

Given that, Pressure at the entry of compressor, P1=1.013 bar,Pressure at the exit of compressor,…

Answered: A single stage reciprocating compressor…

A single stage reciprocating compressor takes 1m³ of air per minute and 1.013 bar and 15°C and delivers at 7 bar. Assuming Adiabatic law (n=1.35) and no clearance.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/min Take “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor if compression is isentropic in kW to 3 decimal places?
Air enters a turbine at temperature and pressure of 800°C, 10bar respectively. The actual exit airtemperature is 180°C. The turbine isentropic efficiency is estimated to be 85%. Calculate the turbine exit pressure and the actual expansion index (n).
Single stage, single-acting air compressor. Air delivery for this device is 30 bar at a speed of 1500 rev/min. The atmospheric condition of his location is 87 kPa and 20 ˚C, with a FAD of 0.22 m2/min. The clearance volume is 4% of the swept volume and the stoke/bore ratio is 1.3/1. Take “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg KW 1.What is the isothermal power of the compressor in kW to 2 decimal places in kW? 2. which formula will be used to evaluate the isothermal efficiency? 3. which formula will be used to evaluate the delivery volume? 4. What is the induced volume in terms of stroke volume, provide the coefficient values of the swept volume to 4 decimal places?
Consider a reciprocating air compressor with 3-stage, 7.2 m3/min free air delivery at atmospheric conditions of 144 kPa and 26 0C, respectively. The polytropic compression index is 1.34, while the delivery pressure is 1,665 kPa. The mechanical and motor-drive efficiencies are 85% and 93%, respectively. Accept complete inter-cooling and neglect clearance volumes. If the specific heat capacity of air at constant pressure and volume are 1.006 kJ/kg K and 0.716 kJ/kg K, respectively. Calculate the rate of heat rejected in the intercooler in kilowatt to 1 decimal place.
Assess the different types of industrial compressor and identify justifiable applications for each while focusing on the working principle and flow direction
Specifications: Altitude = 700m Bypass ratio = 0.5 Speed = 260m/s Total mass flow rate = 15kg/s (in cold flow pipe) The pressure = 0.7bar (in cold flow pipe) Stagnation Temperature = 270K (at the turbine outlet) Stagnation gas pressure = 1.84 bar (at the turbine outlet) Temperature = 687.40C Both nozzles have a 95% efficiency For an aircraft powered by a low bypass ratio turbofan engine: 1a) For the flow expansion via the hot core nozzle, draw a T-s diagram. b) Determine the thrust produced by the hot nozzle. c) Determine the overall thrust produced by the turbofan engine and the thrust generated by the cold nozzle.
The following data were obtained from a performance test of a 10 x 9-cm single acting, water jacketed two-stage air compressor: Pressures: Atmospheric, 102 kPaa; leaving first-stage, 634 kPaa; leaving second-stage, 4.20 MPa. Temperatures: Atmospheric, 240C; leaving first-stage, 1080C; entering 2nd stage, 250C; leaving 2nd stage, 1270C Compressor speed, 648 rpm Power input to motor, 5.65 kW Motor and belt efficiency, 81.5% The following are calculated from test data: Air flow rate, 0.387 ??⁄??? Compression exponents: 1st stage 1.15; 2nd Stage, 1.2 Calculate: a) Approximate indicated power b) Power for isothermal compression c) Shaft power d) 1st stage piston displacement e) Actual volumetric efficiency f) Isothermal compression efficiency g) Mechanical efficiency based on the approximate indicated power h) Over-all efficiency of the compressor
Air enters a reversible compressor steadily and it is compressed from an inlettemperature and pressure of 25 degree C and 88 kpa repsectively. Air leaves the compressor at 800 kpa. Compute the compressor work per unit of mass for an isentropic compression.
Air with a pressure of 0.1 MPa and a temperature of 25oC with a flow rate of 5.29 kg/minute enters a three-stage reciprocating piston compressor with intercooler. The air is compressed polytropically (n = 1.3) to reach the pressure of 4 MPa. Calculate: a) The pressure at stage-2 and stage-3 so that the compression work is minimum? b) The compression work in each stage and the total compression work? c) The outlet air temperature from each stage's cylinder? d) The amount of heat transferred to each intercooler? e) How much air is needed for cooling in the intercooler if the allowable maximum temperature changes between the inlet and outlet of the intercooler is 8oC?
Steam expands in a steam turbine isentropically from intet to exhaust having an enthalpy drop=1200 kJ/kg. Assuming ideal conditions determine the mean diameter of wheel if the turbine were of: (1) Single impulse stage. (i) Single 50% reabron stage.
10 m3 /min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler pressure of 2 bar gauge and polytropic index of 1.3, what is the power consumption of the first stage compressor ? pls choose one a.20.44 KW b.48.8 HP c.22.4 litre/mole d.42.2 bar-m3/min e.25.12 KW
Air at a 800 kPa and 1300 K enters a turbine which has an isentropic efficiency of 90% with a mass ﬂow rate 6 kg/s. The outlet pressure is 100 kPa and assume that speciﬁc heats are constant and evaluated at 600 K. 1. How much power is produced in kW? Round your answer to the nearest whole number. 2. What is the outlet temperature in K? Round your answer to one decimal place. 3. Select all appropriate assumptions Non-ideal gas. Ideal gas Steady flow Unsteady flow Adiabatic Neglect kinetic and potential energy Account for kinetic and potential energy No work Isobaric Isothermal Isochoric Isentropic Exact analysis Approximate analysis