A sinusoidal baseband signal of frequency 5kHz is transmitted using DSB-LC method using (1MHZ, 2V) carrier with u=10%. If the demodulator has input-output characteristics (V, = 3V7) and an IF filter (ideal and unity gain) is used before demodulator with center frequency at 1.002MHZ and 10kHz bandwidth. Find the output signal waveform of this demodulator, as shown: R K De- modulator DC removal LPF IF BPF fk=10kHz U = 3K2

A sinusoidal baseband signal of frequency 5kHz is transmitted using DSB-LC method using (1MHZ, 2V) carrier with u=10%. If the demodulator has input-output characteristics (V, = 3V7) and an IF filter (ideal and unity gain) is used before demodulator with center frequency at 1.002MHZ and 10kHz bandwidth. Find the output signal waveform of this demodulator, as shown: R K De- modulator DC removal LPF IF BPF fk=10kHz U = 3K2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A filter is provided with a cascaded differential amplifier. The midband gain and noise coefficient of the filter are given as −3 dB and 3 dB, respectively.According to this,a) If it is known that the amplifier gain is ?1= 20 dB and the noise coefficient is ?1= 2 dB, calculate the midband gain for the entire cascaded system. Give your answers in dB
Bandwidth requirements:a. Find the minimum required bandwidth for the baseband transmission of a 32-level PAM pulse sequence with a data rate, R of 10000 bps if the system transfer characteristic consists of a raised-cosine spectrum with 100% excess bandwidth (roll-off, r = 1.0).b. Find the minimum required double-sideband (DSB) bandwidth for transmitting the modulated PAM sequence where the system transfer characteristic is the same as in part (a).c. Repeat part (a) with roll-off, r = 0.5.d. Repeat part (b) with roll-off, r = 0.5.e. Repeat part (a) with roll-off, r = 0.f. Repeat part (b) with roll-off, r = 0.
Which of the following is the result when the lower band components of the double sideband signal given the spectrum in the figure are multiplied by cos (Wct) in the signal time space obtained by suppressing the lower band components with a filter?
For an Armstrong indirect FM transmitter with the crystal carrier oscillating at 210 kHz, the crystal reference oscillating at 10.2 MHz, the sideband voltage is 0.018 V, the carrier input voltage to the combiner is 5V, the first and second multipliers are both 40, and the modulating signal frequency is 2 kHz, determine: a.) modulation index at the output of the combining network and the power amplifier; b.) frequency deviation at the same two points; and c.) the transmit carrier frequency.
q/A given AM (DSB – LC) transmitter develops an unmodulated power outputof 1 kW. Across 50Ω resistive load. When a sinusoidal test tone with a peakamplitude of 5? is applied to the input of the modulator, it is found that thespectral line for each sideband in the magnitude spectrum for the output is 40%of the carrier line. Determine the following quantities in the output signal:a-The modulation index.b-The peak amplitude of the lower sideband.c-The ratio of total sideband power to carrier power.d-The total output power.e-The total average power in thr output if the peak amplitude of the modulationsinusoid is reduced to 4 volt.
Chose the correct answer 6- The bandwidth required for a modulated carrier depends on: a) The carrier frequency b) the signal-to-noise ratio c) the signal-plus-noise to noise ratio d) The baseband frequency range
What is the voltage gain (Av) of the circuit when β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 15 kΩ and RL = 248 kω in the circuit given in the figure?Note-1: the output impedance of the transistor r0 will be taken into account in calculations.Note-2: capacitors are negligible at midband frequency.
In the production of Single Sideband with Filter, the baseband signal is band limited between 1kHz and 2kHz and the transmission will be carried out at 40 MHz frequency. How many sequentially balanced modulator structures should there be if practical bandpass filters are used?
What are the relative amplitudes of the fourth pair of sidebands for an FM signal with a deviation ratio of 8?
The modulating signal that is the input into an FM modulator is m(t)=2cos(10??).a) Express the time domain expression of ?(?) signal.b) Express FM signal in terms of Bessel functions.c) Sketch the frequency spectrum of the modulated signal.d) Determine the bandwidth of ?(?) occupies 98% of the total power (Carson Rule) in the acquired spectrum.e) Determine the condition of required bandwidth of ideal BPF if at least 80% of the total power appears at the output of the filter?
What is the quality factor for a 2 MHz carrier and 50 dB sideband suppression with the separation of sidebands of 200 Hz?
amplitude value of output voltage (Vout) = ?? Note1 : E-MOSFET output empedance rd= 70kΩ Note2: capacitors are of negligible size at midband frequency Note3 : 5kHz in midband frequency