A siphon is used to drain water from a tank as illustrated below. Assume steady flow without friction. (a) If h = 1.15 m, find the speed of outflow at the end of the siphon. 4.71 m/s (b) What is the limitation on the height of the top of the siphon above the end of the siphon? Note: For the flow of liquid to be continuous, its pressure must not drop below its vapor pressure. Assume the water is at 13°C, at which the vapor pressure is 1.5 kPa.

A siphon is used to drain water from a tank as illustrated below. Assume steady flow without friction. (a) If h = 1.15 m, find the speed of outflow at the end of the siphon. 4.71 m/s (b) What is the limitation on the height of the top of the siphon above the end of the siphon? Note: For the flow of liquid to be continuous, its pressure must not drop below its vapor pressure. Assume the water is at 13°C, at which the vapor pressure is 1.5 kPa.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 115AP: A sump pump (used to drain water from be basement of houses built below the water table) is draining...

See similar textbooks

Similar questions

A sump pump (used to drain water from be basement of houses built below the water table) is draining a flooded basement at rate of 0.750 L/S, with an output pressure of 3.00105N/m2 . (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses both parts of the problem.
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
A large storage tank with an open top is filled to a height h0. The tank is punctured at a height h above the bottom of the tank (Fig. P15.39). Find an expression for how far from the tank the exiting stream lands. Figure P15.39
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
Water pressure inside a hose nozzle can be less than atmospheric pressure due to the Bernoulli effect. Explain in terms of energy how the water can emerge from the nozzle against the opposing atmospheric pressure.
Water is moving at a velocity of 2.00 m/s through a hose with internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
The gravitational force exerted on a solid object is 5.00 N. When the object is suspended from a spring scale and submerged in water, the scale reads 3.50 N (Fig. P15.24). Find the density of the object. Figure P15.24 Problems 24 and 25.
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
How tall must be to measure blood pressure as high as 300 mm Hg?
An oil gusher shoots crude 25.0 m the through a pipe with a 0.100-m diameter. Neglecting resistance but not resistance of the pipe, and assuming laminar flow, calculate pressure at be entrance of be 50.0-m-Iong vertical pipe. Take of the oil to be 900 kg/m3 and its viscosity to be 100(N/m2) s (or 1.00 Pa s). Note that you must take into account the pressure due to 50.0-m column of oil in pipe.