Water enters a pipeline at a speed of 4 m/s and comes out at a speed of 11 m/s as shown below. If the pressure at point A is 1.5x10 N/m2, what is the pressure at point B? (Use: acceleration due to gravity, g 9.8 m/s and density of Water, Pwater = %3D 1000kg/m)

Water enters a pipeline at a speed of 4 m/s and comes out at a speed of 11 m/s as shown below. If the pressure at point A is 1.5x10 N/m2, what is the pressure at point B? (Use: acceleration due to gravity, g 9.8 m/s and density of Water, Pwater = %3D 1000kg/m)

Name: Water enters a pipeline at a speed of 4 m/s and comes out at a speed
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Water enters a pipeline at a speed of 4 m/s and comes out at a speed of 11 m/s as shownbelow. If the pressure at point A is 1.5x10 N/m², what is the pressure at point B?(Use: acceleration due to gravity, g 9.8 m/s² and density of Water, pwater =%3D1

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter12: Fluid Dynamics And Its Biological And Medical Applications

Section: Chapter Questions

Problem 28PE: A sump pump (used to drain water from the basement of houses built below the water table) is...

See similar textbooks

Similar questions

(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
Concrete is pumped from a cement mixer to the place it is being laid, instead of being carried in wheelbarrows. The flow rate is 200.0 L/min through a 50.0-m-long, 8.00-cm-diameter hose, and the pressure at the pump is 8.00106 N/m2. Verify that the flow of concrete is laminar taking concrete's viscosity to be 48.0 (N/m2) s, and given its density is 2300 kg/m3.
The gravitational force exerted on a solid object is 5.00 N. When the object is suspended from a spring scale and submerged in water, the scale reads 3.50 N (Fig. P15.24). Find the density of the object. Figure P15.24 Problems 24 and 25.
Water flows through a pipe that gradually descends from a height of 6.78 m to the ground. Near the top, the cross-sectional area is 0.400 m2, and the pipe gradually widens so that its area near the ground is 0.800 m2. Water leaves the pipe at a speed of 16.8 m/s. What is the difference in the water pressure between the top and bottom of the pipe?
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
A large storage tank with an open top is filled to a height h0. The tank is punctured at a height h above the bottom of the tank (Fig. P15.39). Find an expression for how far from the tank the exiting stream lands. Figure P15.39
Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?
How tall must a water-filled manometer be to measure blood pressures as high as 300 mm Hg?
An oil gusher shoots crude oil 25.0 m into the air through a pipe with a 0.100-m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the gauge pressure at the entrance of the 50.0-m-long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) s (or 1.00 Pa s). Note that you must take into account the pressure due to the 50.0-m column of oil in the pipe.
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.750 us, with an output pressure of 3.00105 N/m2. (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height, and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses in both parts of the problem.