A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam asshown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b%3D= 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a%3Dcompressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mmbelow the topmost edge of the tee stem at section 1-1. What is the applied load P?P3PВDEStrain gage-dHbAnswer:P =iN

Answered: Image /qna-images/answer/b56732c5-761a-4980-9fc8-17d8d645aedd.jpg

A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P E a a C Strain gage H b Answer:

A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P E a a C Strain gage H b Answer:

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at the midspan. (MPa)
For the figure shown below, If the bending working stresses are 15 ksi in tension and 18 in compression, compute the maximum safe value of P in kips
For the overhanging beam loaded as shown, determine the largest value of P so that the tensile flexure stress is limited to 8000 psi, the compressive bending stress will not exceed 10000 psi, and the transverse stress is limited to 6000 psi
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0525-in. to new position Q' as shown in the figure. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 9 in., b = 1 in., c = 3 in., and Δ=Δ= 0.0525 in.
A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjectedto a tensile load of 1070 kN. The proportional limit of the steel is assumed to be 200 MPa. If thePoisson’s ratio is 0.25, determine the following;a. The transverse strain,b. The total axial deformation, andc. The transverse dimensional change along 300mm.
For the cantilever beam loaded as shown, determine the following:a.) maximum tensile and elastic bending stressesb.) maximum transverse shear stress
A beam has uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at the bottom of the beam section at the midspan (MPa)
NO. 3 Given the beam shown with computed reactions and a cross section. Determine the maximum tensile stress of the section.