A smooth thin plate 5 m long and 1 m wide is placed in air streamed moving at 3 m/s with its length parallel with the flow. Analyse the drag force on each side of the plate. The density of the air is 1.2 kg/m³ and the kinematic viscosity is 1.6 x 10-5 m²/s.

A smooth thin plate 5 m long and 1 m wide is placed in air streamed moving at 3 m/s with its length parallel with the flow. Analyse the drag force on each side of the plate. The density of the air is 1.2 kg/m³ and the kinematic viscosity is 1.6 x 10-5 m²/s.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.24P: Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the...

See similar textbooks

Similar questions

a smooth flat plate of length 5 m and width 2 m is moving with a velocity of 4 m/s in stationary air of density as 1.25 kg/m³ and kinematic viscosity 1.5 x 10-5 m²/s. determine thickness of the boundary layer at the trailing edge of the smooth plate. find the total drag on one side of the plate assuming that the boundary layer is turbulent from the very beginning.
A Savonius rotor can be approximatedby the two open half-tubes in Fig mounted ona central axis. If the drag of each tube is similar to thatin Table 7.2, derive an approximate formula for therotation rate Ω, as a function of U, D, L, and the fluidproperties (ρ, μ).
The standard sea level value of viscosity coefficient for air is μ = 1.7894×10−5 kg/(m · s) = 3.7373 × 10−7 slug/(ft · s). The wing on a Piper Cherokee general aviation aircraft is rectangular, witha span of 9.75 m and a chord of 1.6 m. The aircraft is flying at cruisingspeed (141 mi/h) at sea level. Assume that the skin-friction drag on thewing can be approximated by the drag on a flat plate of the samedimensions. Calculate the skin-friction drag:a. If the flow were completely laminar (which is not the case in real life)b. If the flow were completely turbulent (which is more realistic)Compare the two results.
A thin flat plate 20 cm by 90 cm is immersed in a 1m/s stream of water at 20 °c ( density=998, viscosity=0.001)the stream is parallel to the long side, compute the total friction drag considering both front and back sides of the plate
Q6. Two large fixed parallel planes are 12 mm apart. The space between the surfaces is filled with oil of viscosity 0.972 N.s / m². A flat thin plate 0.25 m² area moves through the oil at a velocity of 0.3 m / s. Calculate the drag force: (1) When the plate is equidistant from both the planes, and (ii) When the thin plate is at a distance of 4 mm from one of the plane surfaces.
plate 450 mm x 150 mm has been placed longitudinally in a stream of crude oil (specific gravity 0.925 and kinematic viscosity of 9.0 x 10-5 m2/s) which flows with velocity of 6 m/s. Calculate: (i) the friction drag on the plate; (ii) the thickness of the boundary layer at a distance 215 mm from the trailing edge;(iii) the thickness of the boundary layer at the trailing edge; (iv) shear stress at the trailing edge.
A) What is an adverse pressure gradient, and where does it occur on an airfoil (Show that onan airfoil using a free hand sketch)?B) What causes the flow to separate from an airfoil?C) What are the two major consequences of flow separation?D) A B-2A aircraft is flying at H ft in standard day conditions at a velocity V kn. If the meanchord length is C ft.i- Find the overall or total Reynolds number for the aircraft.ii- Find the percentage of the wing chord where laminar flow is present, if Reynoldsnumber is 500,000.
We are testing a flat plate of length L = 1.125 m and width W = 0.225 m in a stream of air flowing with a velocity of 20 m/s. In test case 1, the air is flowing parallel to L and in test case 2 air is flowing parallel to W. Find: What portion of the boundary layer flow is laminar in each case? What is the highest laminar boundary layer thickness in each case? Assuming the flow is entirely turbulent over the plate, calculate the drag force in both test cases Take air density as 1.2 kg/m3 and its viscosity as μ=18×10−6μ=18×10−6 N.s/m2.
Assume that a radioactive dust particle approximates asphere of density 2400 kg/m3. How long, in days, will ittake such a particle to settle to sea level from an altitude of12 km if the particle diameter is (a) 1 μm or (b) 20 μm?
Air at 20°C and 1 atm flows at 3 m/s past a sharp flat plate2 m wide and 1 m long. (a) What is the wall shear stress atthe end of the plate? (b) What is the air velocity at a point4.5 mm normal to the end of the plate? (c) What is the totalfriction drag on the plate?
The purpose of this problem is to give you a feel for the magnitude ofReynolds number appropriate to real airplanes in actual flight. a. Consider the DC-3 shown in (1.1). The wing root chord length(distance from the front to the back of the wing where the wing joinsthe fuselage) is 14.25 ft. Consider the DC-3 flying at 200 miles perhour at sea level. Calculate the Reynolds number for the flow over thewing root chord. (This is an important number, because as we will seelater, it governs the skin-friction drag over that portion of the wing.)b. Consider the F-22 shown in (1.5), and also gracing the cover ofthis book. The chord length where the wing joins the center body is21.5 ft. Consider the airplane making a high-speed pass at a velocityof 1320 ft/s at sea level (Mach 1.2). Calculate the Reynolds number atthe wing root.
An aircraft is flying in level flight at a speed of 200 km / hr through air density 1.2 kg/ m ^2 and viscosity 1.6 × 10^-5 Ns/m^2. The lift coeffient is 0.4 and the mass of the aircraft is 800 kg. Calculate the effective lift area of the aircraft.