A soil sample 10 cm in diameter is placed in a tube 1.2 m long. A constant supply of water is allowed to flow into one end of the soil at A and the outflow at B is collected by a beaker. The average amount of water collected is 2 cm3 for every 10 seconds. Determine the hydraulic gradient. Ans: 0.667

A soil sample 10 cm in diameter is placed in a tube 1.2 m long. A constant supply of water is allowed to flow into one end of the soil at A and the outflow at B is collected by a beaker. The average amount of water collected is 2 cm3 for every 10 seconds. Determine the hydraulic gradient. Ans: 0.667

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

9. From the figure shown: (See picture below) Cross-sectional area = 0.6m2 Hydraulic Conductivity of sand = 0.1 cm/sec What is the rate of upward seepage of water? (Answer: 360 cm3/sec) What would be the critical hydraulic gradient? (Answer: 1.12 m) What value of h to cause boiling? (Answer: 2.8 m)
The figure below shows the layers of soil in a tube 100 mm x 100 mm in cross section. Water is supplied to maintain a constant head difference of H across the sample. Hydraulic conductivities of each soil are tabulated below. All measurements in the figure are millimeters. If H = 1.98 and the Hydraulic conductivity of soil E is 0.002 m/s. a. Determine the equivalent hydraulic conductivity of the system in the direction of the flow. b. Find the h1 and h2. c. Determine the rate of flow.
A soil sample 15 cm in diameter is placed In a tube 2 m long. A constant supply of water is allowed toflow into one end of the soil at A and the outflow at B is collected by a beaker. The average amount ofwater collected is 2 cubic centimeter every 5 seconds. The tube is inclined and has a head differenceof 2.5 m. Determine the following 1. Hydraulic Gradiant. 2. Flowrate in cm/s. 3. Discharge Velocity in cm/s. 4. Seepage velocity in cm/s if porosity is 0.420. 5. Hydraulic Conductivity.
Solve for the ratio of equivalent hydraulic conductivity with the following given: h1 = 2 m h2 = 2.5 m h3 = 1.8 m h4 = 0.9 m k1 = 1.5E-3 cm/sec k2 = 2.2E-4 cm/sec k3 = 1.6E-4 cm/sec k4 = 4.0E-4 cm/sec What is the equivalent coefficient of permeability if the water flows perpendicular to the layer of soil (KeqV) in cm/sec?
8. The figure shows the layers of soil in a tube that is 100 mm x 100 mm in cross section. When supplied to maintain a constant head difference of 300 mm across the sample. The hydraulic conductivity of the soils in the direction to flow to them are as follows: Soil A = 2 x 10 ^ -2 cm/sec Soil B = 3 x 10 ^ -3 cm/sec Soil C = 4 x 10 ^ -4 cm/sec (See picture below) Find the equivalent hydraulic conductivity Find the hydraulic gradient Find the rate of water supply in cm3/hr.
Solve for the ratio of equivalent hydraulic conductivity with the following given: h1 = 2 m h2 = 2.5 m h3 = 1.8 m h4 = 0.9 m k1 = 1.5E-3 cm/sec k2 = 2.2E-4 cm/sec k3 = 1.6E-4 cm/sec k4 = 4.0E-4 cm/sec What is the equivalent coefficient of permeability if the water flows parallel to the layer of soil (KeqH) in cm/sec?
1. Calculate the equivalent hydraulic conductivity for the soil profile shown in figure 2. An excavation is proposed for a square area near the bend of a river, as shown in figure. It is expected that the flow of water into the excavation will come through the silt layer. Pumping test reveal an average horizontal hydraulic conductivity of 2 x 10 -5 cm/s in the silt layer. The excavation has to be kept dry. Determine the flow (qs) into the excavation.
For a falling head laboratory test, the following are the given values:• Length of soil specimen = 480.0 mm• Initial head = 700.00 mm• Final head = 395.00 mm• Duration of test = 5.5 mins• Area of standpipe = 0.97 sq.cm• Area of specimen = 18.0 sq.cmA. Compute for the hydraulic conductivity of the soil in cm/sec.B. Determine the head difference at t = 3.50 mins.
Three piezometers have been installed in the confined aquifer shown in Figure 2 below. The aquifer has a uniform thickness of 3.5 m and a hydraulic conductivity of 2x10-1 cm/s. Determine the hydraulic gradient, the direction of flow, the transmissivity, and the flow rate per unit width of the aquifer.
Figure below shows layers of soil in a tube that is 100mm x 100mm incross section. Water is supplied at a constant head difference of 400 mm across thesample. The hydraulic conductivities of the soils in the direction of flow through them areas follows. Soil k (cm/sec) Porosity, n (%) A 1x10-2 25 B 3x10-3 32 C 4.9x10-4 22 a. Calculate the equivalent k in cm/sec.b. Calculate the rate of water supply in cm^3/hrc. Calculate the seepage velocity through soil C in m/sec.
11. A channel runs almost parallel to a river as shown in the figure. The water level in the river has an elevation of 36 m. and the elevation of the channel is 33 m. The river and channel are 600 m apart and a previous formation of the average thickness of 9 m and hydraulic conductivity of 0.80 m/hr joints them together. Compute the hydraulic gradient Compute the rate of seepage flow from the river to the channel per meter width in liters per day. If the seepage velocity is 0.048 m/day, compute the void ratio of the previous medium.
A falling head hydraulic conductivity test is performed on a sample of soil. The standpipe. having a diameter 0.35 cm is observed and it takes 80 seconds for the water to drop by 70 cm from an initial hydraulic head of 90 cm. The sample has a length of 22 cm, and a diameter of 5 cm. Compute the rate of flow of water in the soil (in cm³/s). Answer in 3 decimals Pls answer asap