A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to45000 W at 1800 rev/min. If the maximum allowable shear stress is 60 MN/m?Q4and the modulus of rigidity, G = 79 GPa, determine the following:c)The relative angle of twist of the ends of the shaft

Answered: Image /qna-images/answer/b97c2a06-0cc7-4a97-a8e3-6c33a7a89180.jpg

A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800 rev/min. If the maximum allowable shear stress is 60 MN/m2 and the modulus of rigidity, G = 79 GPa, determine the following: Q4 c) The relative angle of twist of the ends of the shaft

A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800 rev/min. If the maximum allowable shear stress is 60 MN/m2 and the modulus of rigidity, G = 79 GPa, determine the following: Q4 c) The relative angle of twist of the ends of the shaft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.5P: A stepped shaft ACB having solid circular cross sections with two different diameters is held...

See similar textbooks

Related questions

Q: A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800 ...

Q: A pulley 250 mm in diameter drives a second pulley 1,000 mm in diameter by means of a belt as seen F...

Q: Assuming the sea water to be incompressible (w = 10070 N/m3), what is the pressure in bars, 2300 m. ...

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has...

Q: 2. (a) Bring out the advantages and disadvantages of using a hydraulic system with a suitable applic...

A: Hydraulic system make use of liquids usually hydraulic oil to convert fluid pressure into useful wor...

Q: When an axial load is applied to the ends of the bar shown in the figure, the total elongation of th...

Q: Q1. A rectangular gate is hinged at the water line, as shown. ) Draw a FBD of the gate, complete wit...

Q: A two stroke spark ignition engine is running at 2000 rpm, compute the time (in milli second) for co...

Q: How does resonance occurs in a dynamic system? What must I take into account from preventing this fr...

A: Introduction: In a dynamic system when the forced frequency becomes equal to the natural frequency o...

Q: In each duct (A and C), air conditioning processes described below take place: In the AB duct, a coo...

A: Given data: at A , temperature = TA = 45oC at A, humidity = 10% at B, humidity = 80% Atmospheric Air...

Q: If atmospheric pressure is 13.8 psia and a gage attached to a tank reads 8.3 inHg vacuum, find the a...

A: Given: The atmospheric pressure is Patm=13.8 psia. The gauge pressure is h=8.3 in mercury in vacuum...

Q: initial vertical acceleration is 7.6 m/s2. Calculate the total mass of the rocket and fuel in at lau...

Q: How does the Orifice Meter equipment measure and record the kinetic and potential energy of a flowin...

A: Orifice meter is flow measuring device made of a hole in a plate which works by measuring the differ...

Q: Calculate the Mach number of the exit if the diverging duct has an inlet area and velocity of air of...

A: Given:- Inlet area = 0.5 m2 Inlet velocity = 60 m/s Outlet area = 8×0.5 = 4 m2 To Find :- Mach n...

Q: Problem 2. For the single-degree-of-freedom mechanical system shown in the figure, the bar has mass ...

Q: Compare and contrast between hydraulic, pneumatic and electro mechanical power system

Q: According to the Mesa LID project video, the following are the principles of low impact development:...

A: 1) the answer is true because all the 3 points are mentioned in the video.

Q: a) Calculate the instantaneous angular acceleration a, in rad/s? at t = 2.88 s. Insert your answer c...

Q: 14) Which one of the following is correct about an IC engine from the perspective of automotive powe...

Q: Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the con...

Q: height of mercury column

A: height of mercury column

Q: A diesel engine has a bore of 4 in., a stroke of 4.3 in., and a compression ratio of 19:1 running at...

A: Given Data: Diameter of the cylinder, d=4 in Stroke length, l=4.3 in Revolutions per min, N=200 rpm...

Q: If you have a half circle made of steel and the other half of wood, is the center of the circle equa...

Q: is applied through the rigid cover plate shown

A: calculation in contraction in the length due to temperature contraction in aluminium =∆AL∆A...

Q: A mass m = 4 kg is attached to both a spring with spring constant k = 101 N/m and a dash-pot with da...

Q: equipped with regenerative as well as reheat arrangement. The steam is supplied at 80 bar and 55°C o...

Q: 5. What will be the accuracy of

A: Need to find accuracy .

Q: 7. One area of agreement among the three Gurus (Deming, Juran, and Crosby) is the importance of mana...

A: Total Quality Management and it's development in the 20th century was heavily contributed by Deming,...

Q: A 2.5 N weight has a kinetic energy 1.75 J. Determine its velocity in kph.

Q: the constants 1, m, and m

A: L , m , n are the constrains of above equations.

Q: An orifice meter with 150 mm diameter is inserted in a pipe of 300 mm the pressure difference measur...

A: Given that, d0=0.15 m, d1=0.30m Specific Gravity of mercury, SHg=13.6 Specific Gravity of oil, So=0...

Q: A rectangular plane surface is 2 m wide and 3 m deep. It lies in a vertical plane in seawater. Deter...

Q: ʟɪQᴜɪᴅ ᴀᴍᴍᴏɴɪᴀ ᴀᴛ ᴀ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ᴏꜰ 26 degree ᴄelsius ɪꜱ ᴀᴠᴀɪʟᴀʙʟᴇ ᴀᴛ ᴛʜᴇ ᴇxᴘᴀɴꜱɪᴏɴ ᴠᴀʟᴠᴇ . ᴛʜᴇ ᴛᴇᴍᴘᴇ...

Q: . How is heat loss calculated in bare and lagged pipes? b. What is heat loss calculation in insulat...

A: NOTE: According to Bartleyby's policy we shall answer only three sub-parts at a time so kindly repos...

Q: If the specific volume of a gas is 389 ft3/slug, what is its specific weight in lb/ft3?

A: Specific volume = 389 ft3/slug Density of gas = 1/389 slug /ft3 specific weight = density × g ...

Q: the slider crank mechanism shown in Fig. 2-29, the crank is rotating at 200 rpm. Determine the veloc...

A: Given:N=200 rpmθ=30°r=600 mml=2500 mm

Q: 2. The horizontal rod OA rotates about a vertical shaft according to the relation 0 = 3t°, where 0 a...

A: Dear student, According to the guidelines I am allowed to answer only three sub-p...

Q: (1) Steam at a temperature of 250°C has a specific volume of 0.15436m/kg. What are the pressure, spe...

Q: When the clutch pedal is released on a hydraulic clutch linkage, the ___.a. master cylinder piston i...

A: The clutch allows engine power to be supplied gradually when a vehicle is first started and pause...

Q: What manages turbo output by controlling theamount of exhaust gas entering the turbinehousing?a. Was...

A: The turbine and the compressor are the two primary parts of a turbocharger. These are referred to...

Q: 6-1 The operuting point of a fan-and-duct system is to be determined. The equations for the two coin...

Q: A simply supported beam, 6m in length, has an initial deflection of 0.50mm at midspan due to its own...

A: (1) The weight will act like an uniform load throughout the length of the beam. so write the express...

Q: A pressure relief valve contains a poppet with a 4.20 cm2 area on which system pressure acts. During...

Q: Torsion of bars with thin-walled open cross sections. Consider a bar with the cross section shown in...

A: TORSION OF BARS WITH THIN WALLED OPEN CROSS SECTIONS In the customary speculations of twist of sle...

Q: The bracket, which is fastened to a wall by anchor bolts at A and B, is loaded by the force P = 140 ...

Q: Briefly describe the process and then identify at least one type of product which can be manufacture...

A: given; Briefly describe the process and then identify at least one type of product which can be manu...

Q: e working of a cent

A: introduction: in this question we explain about centerless grinding operation.

Q: A thin-walled tube is subjected to torsion as shown. Determine the angle of twist produced. (in rad)

A: Given Radius =300 mm = 0.3 m Length = 6 m Thickness = 25 mm = 0.025 m T = 4kN m = 4000 Nm G = 70 GPa...

Q: A fan delivers 5.1 m^3/sec at a static pressure of 6.167 cm of water when operating at a speed of 60...

Q: 9) Which one of the following helps in the reduction of NOx in a catalytic converter? O Platinum O P...

A: We will answer the first question since the exact one was not specified. please submit a new questio...

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to
45000 W at 1800 rev/min. If the maximum allowable shear stress is 60 MN/m?
Q4
and the modulus of rigidity, G = 79 GPa, determine the following:
c)
The relative angle of twist of the ends of the shaft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A stepped shaft consisting of solid circular segments having diameters D1= 2.0 in, and D2= 2.4 in. (see figure) is subjected to torques T. The radius of the fillet is R = 0,1 in. If the allowable shear stress at the stress concentration is 6000 psi, what is the maximum permissible torque Tmax?
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A thin-walled steel tube of rectangular cross section (see figure) has centerline dimensions b = 150 mm and h = 100 mm. The wall thickness t is constant and equal to 6.0 mm. Determine the shear stress in the tube due to a torque T = 1650 N · m. Determine the angle of twist (in degrees) if the length L of the tube is 1.2 m and the shear modulus G is 75 GPa.
A solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at 300 r.p.m. It was recommended that the maximum shear stress and angle of twist are limited to 60 MPa and 1.5 degrees respectively. Determine the diameter and length of the shaft. For the shaft material, G= 80 GPa.