solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at 300 r.p.m. It was recommended that the maximum shear stress and angle of twist are limited to 60 MPa and 1.5 degrees respectively. Determine the diameter and length of the shaft. For the shaft material, G= 80 GPa.

solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at 300 r.p.m. It was recommended that the maximum shear stress and angle of twist are limited to 60 MPa and 1.5 degrees respectively. Determine the diameter and length of the shaft. For the shaft material, G= 80 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Similar questions

The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter do of the solid shaft. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts. 1
A steel shaft transmits 30 kW of power at 10 Hz. Determine the smallest safe diameter of the shaft if the shear stress τmax is not to exceed 50 MPa and the angle of twist θ is limited to 5°in a length of 4 m. Use G = 70 GPa
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
Torsion Problem 6.0 A solid steel shaft is to transmit 5 hp from the motor to which it is attached. If the shaft rotates at w=160rpm and the steel has an allowable shear stress T=14 ksi, determine the required diameter of the shaft.
A solid shaft is to transmit 22kW at 110 rpm. Determine the diameter of the shaft if the shearing stress is not exceed 35 MPa and the angle of twist is limited to 5 degrees in a length of 4m. Use G=86 GPa.
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to atorque of 12 KN"m. The modulus of rigidity of the steel shaft is 83 GPa. Determine;a) Diameter of the shaft.and Maximum shearing stress developed in the shaft.
A hollow circular shaft with the ratio of internal and external diameters of 0.6 is required to transmit 870 kW at 120 rpm, the maximum torque being 20% greater than the mean. Determine the dimensions of the shaft if the maximum shearing stress and twist in a length of 3m are limited to 60Mpa and 1.4°respectively. The G= 80Gpa.