A solid shaft of 20 mm radius is transmitting 2.5 kW with the frequency of 50 Hz. Calculate the maximum shear stress. = 1.266 MPa (A) T max (B) T max (C) Tmax (D) T max = 0.633 MPa = 1.899 MPa = 0.9495 MPa

A solid shaft of 20 mm radius is transmitting 2.5 kW with the frequency of 50 Hz. Calculate the maximum shear stress. = 1.266 MPa (A) T max (B) T max (C) Tmax (D) T max = 0.633 MPa = 1.899 MPa = 0.9495 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: a reversed Carnot cycle has a refrigerating COP of 5. - What is the ratio TH/TL? - If the work…

A: Given Data- COP of refrigeration cycle =5 We have to find all points given in question

Q: What does the Property process include exactly?

Q: if air is at pressure of 2200 lb/ft^3, and at a temperature of 800°R, what is the specific volume

Q: Two hundred kg/hr of air at 28°C and 50% relative humidity is then heated to 50°C, passed through an…

A: Given Data The temperature at the first condition is: T1=28°C The temperature at the second…

Q: The rod OA rotates in the horizontal plane such that 0=0.72+³ radian, and collar B is sliding…

A: Given data: θ=0.72t3r=80t2r=108 mm Need to determine the transverse acceleration.

Q: A glass tube is inserted in mercury shown in figure below; the common temperature is 20°C. What is…

Q: A block of mass 2 kg is attached with a spring as shown in the figure. Calculate the natural…

Q: Problem 2: At the instant shown the 75-kg block A is moving up the plane at 5 m/s while attached to…

Q: A motorist starts from rest at point A on a circular entrance ramp when t=0, increases the speed of…

Q: A disk is driven by a motor such that the angular position of the disk is defined by 0 =(141+1412)…

A: Here, angular position, θ=(14t+1.4t2) rad and angular velocity, ω=dθdt=(14+2.8t) rad/s

Q: Problem 2 - The shaft OBCD is acted upon by 2 forces T = 50 lbs., and F= 200 lbs., as shown. Find:…

Q: A hollow circular steel shaft with an outside diameter of 2.906. and a wall thickness of 0.437 in.…

Q: 4a) A Ship must discharge a total of Seawater ballast 2200 cubic meters of Within 6 hours. Using S…

A: given; (a)discharge volume=2200m3at time (t)=6 hours =6*3600 secdiameter of…

Q: 3.13 A house has a composite wall of wood, fiberglass insula- tion, and plaster board, as indicated…

Q: The motion of a particle is defined by the relation x = at² - b(t -2)³ where x and t are expressed…

Q: The smooth surface of the vertical cam is defined in part by the curver (0.2 cos 0+0.3) m. (Figure…

A: Given Dataθ˙=4 rad/sr=0.2cosθ+0.3k=30N/mm=0.9kgθ=30°

Q: 1.2 L car engine has four individual cylinders, each one of which holds 0.3 L of fuel + air gas…

Q: standard vapor compression cycle a condensing temperature of 36 The heat extraction rat

A: GivenStandard vapour compression cycleRefrigerent =R134aT2'=36oCT1=-5oCQL=30kW

Q: How does a microcontroller function? What is it? In robotics, what function does the microcontroller…

A: Microprocessor

Q: Is reconstitution the act of mixing a liquid with a powder to make a liquid form?

Q: Air is used at a rate of 45 cfm from a receiver at 105°F and 125 psi. If the atmospheric pressure is…

Q: Disposal Instruction of CNC milling machine

A: CNC Milling Machine: CNC Milling Machines are programmed machine which operates cutting tools and…

Q: A refrigeration system operates on an ideal vapor-compression using R-12 with a vaporizing…

A: Given:Vaporizing temperature, TL=-10°CCondensing temperature, TH=30°CCompressor power, P=10 kWh2=375…

Q: A solid steel shaft is subjected to a variable torque whose maximum value is 710 N-m. For a fatigue…

Q: The rod OA rotates in the horizontal plane such that 0=0.57t³ radian, and collar B is sliding…

Q: e help culate the Moment of Inertia of the rectangle of 0 mm and height 10 mm about its centroidal…

A: Data available:Base of the rectangle, b=80 mmHeight of the rectangle, h=10 mm

Q: 3.39 The diagram shows a conical section fabricated from pure aluminum. It is of circular cross…

A: For solution refer below images.

Q: There are ten (10) stud bolts on the cylinder head of a 203 mm x 304 mm ammonia compressor. The…

A: Givennumber of bolt n=10cylinder head area A=203mm×304mm=20.3 cm×30.4 cmPressure P=31 kg/cm2

Q: Write a note on toughness mechanism in brief. What is the standard size of square and round test…

A: Impact Test The…

Q: 2 G 1.74m 57m ← B 가 1.75m .56m BG's magnitude 438 N 1m 1.5m 1.5m

A: Given data Magnitude of force BG = 438 N Find the magnitude of only x component of BG.

Q: . Estimate the heat-transfer rate per foot of length from a 0.02-in. diameter nichrome wire immersed…

A: As per our guidelines, we can answer only one question. Kindly post the remaining question in…

Q: A closed cylindrical tank 2m in diameter and 8m deep with axis vertical contains 6m deep of oil (sp.…

A: Given that: diameter of the tank is 2 m height of the tank is 8 m height of the oil is 6 m specific…

Q: The pressure outside the droplet of water of diameter 0.04 mm is 103.2 kPa (atmospheric pressure).…

A: Given:Diameter of the water droplet, d=0.04 mmAtmospheric pressure, Patm=103.2 kPaSurface tension,…

Q: 2. d. the specific enthalpy of compressed liquid water at P = 20.0 MPa and T = 40 °C. Determine the…

A: Given: d) Pressure = 20 MPa Temperature = 40 °C 2) Pressure = 15 MPa Temperature = 100 °C

Q: fluid with a vapor pressure of 0.2 Pa and a specific gravity of 12 is used in barometer. If the…

Q: The curved surface is a circular arc with a radius of 5 m and a width of 4 m into the paper. The…

A: Givenr=5mw=4md=9m

Q: The telephone pole AB weighing 3730 N is resting in a hole that is 2m deep. If the contact force…

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

Q: 2.83 A crate is supported by three cables, as shown. Determine the weight W of the crate, knowing…

Q: A wheel has an initial clockwise angular velocity of 12 rad/s and a constant angular acceleration…

Q: Show the tolerance zone created by each of the given tolerance specifications. Superimpose the…

A: We have to show the tolerance zone created by each of the given tolerance specification. And,…

Q: 7- Listed in the tables are five springs described in SI units. Investigate these squared-…

Q: Find dy dx

Q: A. The food compartment of a refrigerator, shown in fig., is maintained at 4°C by removing heat from…

A: For a refrigerator, rate of heat removed is 360000 J/min. Net work input is 2 kW It is required to…

Q: An accelerometer is composed of weight W=0.042 lb suspended by a spring for which k = 5 lb/in., and…

A: Given: Weight, W = 0.042 lb Stiffness, k = 5 lb/in = 60 lb/ft Damping factor, ζ=0.65 Frequency,…

Q: Determine the required magnitude of F1, F2, and F3 so that the resultant couple moment is

A: Moment:- Moment of any force is the measure of its tendency to rotate a body about its axis. It is…

Q: A mild steel rod of 12mm diameter was tested for tensile strength with the gauge length of 60mm.…

A: Given data: ● The initial diameter and gauge length of the mild steel rod: do = 12 mm , Lo = 60 mm ●…

Q: Q3: Michal has a 100-acre farm and plans to plant at most three crops. The seed for crops A, B and C…

Q: A hydraulic cylinder AB produces a 1,600 lb compressive force. Determine the force in member BC.

Q: Q4: A. Calculate the pressure of steam at a temperature of 500°C and a density of 24 kg/m³ using (a)…

A: Given data: temperature T=500°C Density ρ=24 Kg/m3 here assume gas constant of steam at 500°C…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A solid shaft of 20 mm radius is transmitting 2.5 kW with the frequency of 50 Hz.
Calculate the maximum shear stress.
(A) Tmax
(B) T
max
= 1.266 MPa
max
= 0.633 MPa
(C) T
(D) Tmax=0.9495 MPa
= 1.899 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed torque t1acting aver segment 1 and concentrated torque t2applied at C, as shown in the figure. Segment 1 of the shaft has a diameter of d1= 57 mm and length of L1= 0.75 m; segment 2 has a diameter d2— 44 mm and length L2= 0.5 m. Torque intensity /,"= 3100 N . m/m and T2= 1100 N. m. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: .x = L1/2 and at .x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?