4a) A Ship must discharge a total of2200 cubic metersSea water ballastWithin 6 hours. Using S SNAMEreccomended fluid Velocity, size andSelect the appropriate scha 40 Steelpipe. What is the actual velocity?total head is6) Calculate the power to drive the ballastpump in part a) if the65m. What power would be requiredthe ship was in fresh water?(Sea water SG: 1.025, freshwater :171)

given; (a)discharge volume=2200m3at time (t)=6 hours =6*3600 secdiameter of…

4a) A Ship must discharge a total of Seawater ballast 2200 cubic meters of Within 6 hours. Using S SNAME reccomended fluid Velocity, size Select the appropriate and Schd 40 Steel pipe. What is the actual velocity? total head is 6) Calculate the power to drive the ballast pump in part a) if the 65m. What power would be required. the ship was in fresh water? (Sea water SG: 1.025, freshwater: 14 (1)

4a) A Ship must discharge a total of Seawater ballast 2200 cubic meters of Within 6 hours. Using S SNAME reccomended fluid Velocity, size Select the appropriate and Schd 40 Steel pipe. What is the actual velocity? total head is 6) Calculate the power to drive the ballast pump in part a) if the 65m. What power would be required. the ship was in fresh water? (Sea water SG: 1.025, freshwater: 14 (1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

This problem is useful for the preliminary design of a hydroturbine. From the material learned in this chapter, it is fairly simple to estimate how much power a hydroturbine can generate, given only the flow rate of water and the elevation difference upstream and downstream of the dam. A dam has a gross head of 15.5 m and a flow rate of 0.22 m3 /s. Approximating the overall efficiency of the turbine/generator to be 75%, estimate the electrical power (in kW) that couldbe produced.
What is the gross head (m) of a small hydroelectric dam that can produce 10 kW ofpower if the penstock discharge is 1,500 li/min?
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?
Gentlemen, please check and help me with question #3 Tank filled with water and orifice diameter of 3 cm in the bottom. Height between centre of orifice and water level 3 m. Coefficient of discharge - 0.64, coefficient of velocity- 0.97. Find: 1. Actual jet velocity? This one I know how to do. V(actual) = square root from 2gH 2. Jet diameter? This one I know as well. Coefficient of contraction= coefficient of discharge/ coefficient of velocity Diam of jet we will find from formula: Coefficient of contraction = (diameter of jet/diameter of orifice)^2 3. How long will it take for jet to be established?
A two floor building has two faucets, one in the basement and one in the first floor. The maximum water (\rho = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 12m/s. The faucet diameter is 1.5 cm. Neglect all losses. (a) How much is the maximum velocity at the first floor faucet, when the basement faucet is closed? (b) What would be a maximum height (from the basement floor) for a faucet, to still get a maximum exit velocity of 5 m/s?
In Fig. , let Vo = 5.5 m/s and yo = 90 cm. (a) Will thewater rise or fall over the bump? (b) For a bump height of30 cm, determine the Froude number over the bump. (c) Findthe bump height that will cause critical fl ow over the bump.
Define Upstream and Down Stream.
Find the flow rate, net head, and efficiency of the pumps if they are operating separately. Show on the graph you have drawnas a representative how you have determined by using the graph. Using the graphs, show your selection and calculations onthe graph (you can draw the graphs on excel) ÖN=5
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4.5 times the velocity head in the siphon. Determine the flow rate in the siphon in lit/sec Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: li/s Decimal Places required in the final answer: 3
A water jet has a diameter of 75mm and ahs a velocity of 15m/s. What is the horsepower exerted by the jet. ANSWER: 10hp