A solution is prepared that is initially 0.34M in acetic acid (HCH,CO,) and 0.066M in sodium acetate (NaCH,CO,). Complete the reaction table below, so that you could use it to calculate the pH of this solution. Use x to stand for the unknown change in [H,0"]v Initial change final [MCH,Ca_] [cu,ca] 0 0 0 0 0 You can leave out the M symbol for molarity [10] 0 0 0 8 cla

A solution is prepared that is initially 0.34M in acetic acid (HCH,CO,) and 0.066M in sodium acetate (NaCH,CO,). Complete the reaction table below, so that you could use it to calculate the pH of this solution. Use x to stand for the unknown change in [H,0"]v Initial change final [MCH,Ca_] [cu,ca] 0 0 0 0 0 You can leave out the M symbol for molarity [10] 0 0 0 8 cla

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter15: Solutions Of Acids And Bases

Section: Chapter Questions

Problem 15.121QE: A solution is made by diluting 25.0 mL of concentrated HCl (37% by weight; density = 1.19 g/mL) to...

See similar textbooks

Similar questions

A solution is made by diluting 25.0 mL of concentrated HCl (37% by weight; density = 1.19 g/mL) to exactly 500 mL. Calculate the pH of the resulting solution.
Ammonia gas is bubbled into 275 mL of water to make an aqueous solution of ammonia. To prepare a buffer with a pH of 9.56, 15.0 g of NH4Cl are added. How many liters of NH3; at 25C and 0.981 atm should be used to prepare the buffer? Assume no volume changes and ignore the vapor pressure of water.
A 10.00-g sample of the ionic compound NaA, where A is the anion of a weak acid, was dissolved in enough water to make 100.0 mL of solution and was then titrated with 0.100 M HCl. After 500.0 mL HCl was added, the pH was 5.00. The experimenter found that 1.00 L of 0.100 M HCl was required to reach the stoichiometric point of the titration. a. What is the molar mass of NaA? b. Calculate the pH of the solution at the stoichiometric point of the titration.
A buffer solution is prepared by adding 5.50 g of ammonium chloride and 0.0188 mol of ammonia to enough water to make 155 mL of solution. (a) What is the pH of the buffer? (b) If enough water is added to double the volume, what is the pH of the solution?
You have a solution of the weak acid HA and add some of the salt NaA to it. What are the major species in the solution? What do you need to know to calculate the pH of the solution, and how would you use this information? How does the pH of the solution of just the HA compare with that of the final mixture? Explain.
You have 0.10-mol samples of three acids identified simply as HX, HY, and HZ. For each acid, you make up 0.10 M solutions by adding sufficient water to each of the acid samples. When you measure the pH of these samples, you find that the pH of HX is greater than the pH of HY, which in turn is greater than the pH of HZ. a Which of the acids is the least ionized in its solution? b Which acid has the largest Kd?
Ka for formic acid is 1.7 104 at 25C. A buffer is made by mixing 529 mL of 0.465 M formic acid, HCHO2, and 494 mL of 0.524 M sodium formate, NaCHO2. Calculate the pH of this solution at 25C after 110 mL of 0.152 M HCl has been added to this buffer.
A buffer is prepared by dissolving 0.0250 mol of sodium nitrite, NaNO2, in 250.0 mL of 0.0410 M nitrous acid, HNO2. Assume no volume change after HNO2 is dissolved. Calculate the pH of this buffer.
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
The species called glacial acetic acid is 98% acetic acid by mass (d=1.0542g/mL). What volume of glacial acetic acid must be added to 100.0 mL of 1.25 M NaOH to give a buffer with a pH of 4.20?
A diprotic acid, H2B(MM=126g/moL), is determined to be a hydrate, H2B xH2O. A 10.00-g sample of this hydrate is dissolved in enough water to make 150.0 mL of solution. Twenty-five milliliters of this solution requires 48.5 mL of 0.425 M NaOH to reach the equivalence point. What is x?
A friend asks the following: Consider a buffered solution made up of the weak acid HA and its salt NaA. If a strong base like NaOH is added, the HA reacts with the OH to form A. Thus the amount of acid (HA) is decreased, and the amount of base (A) is increased. Analogously, adding HCI to the buffered solution forms more of the acid (HA) by reacting with the base (A). Thus how can we claim that a buffered solution resists changes in the pH of the solution? How would you explain buffering to this friend?