A source of AC emf E₁ = 120/30º volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E2 = 120/-300 volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. О а. O a. 7.62 amperes O b. 4.42 amperes O c. 5.38 amperes O d. 6.48 amperes

A source of AC emf E₁ = 120/30º volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E2 = 120/-300 volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. О а. O a. 7.62 amperes O b. 4.42 amperes O c. 5.38 amperes O d. 6.48 amperes

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
1.1 We have two loads in delta and another in star in parallel, the impedances of the branches of the delta are equal and we have that RΔ=1p.u. and XΔ=0.75 p.u., while in the star we have equal values of the branches, but formed by admittances where we have the conductance in parallel GY=0.64 p.u. and inductive susceptance of BY=-j0.48 p.u. If the loads are being supplied by a positive sequence balanced three-phase source with line-to-line voltage of phases a and b of Vab=1∠ 30º, if the base values are line-to-line base voltage of 1kV and three-phase base power of 100kW. DetermineA) Line and phase voltages, line and phase currents of the load in delta, line and phase voltages of the star, line and phase currents of the star.B) Obtain separately the phasor diagram of the delta and star load with the values obtained in A), indicate on the scale that these are 1 p.u.=5cm for example.C) obtain the power triangle and the power factor separately for each load. D) Obtain the power…
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
IDSS=8mA , VP =-4VTo help plot the DC load line VGS=VG-IDRSa)Determine the value of Vgs when ID=1mAb)Determine the value of Vgs when ID=2mAc)Determine the value of Vgs when ID=3mAd)Determine the value of Vgs when ID=4mAe)Attach a Plot of JFET Characteristic Curve as shown in Figuref)What is the approximate VGSQ?g)What is the approximate IDQ in mA?h)Determine source voltage VS.i)Calculate the drain voltage VD.j)Calculate the drain-to-source voltage VDS.
Estimate the distance over which a load of 15000 KW at p.f-0.8 lagging can be delivered by a 3-phase T.L having conductor each of resistance 0.8 2 per km the voltage at the receiving end is to be 132 KV and the losses in the line is to be 5% of received power
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
Question oneA balanced star connected load comprises of 20 ohm resistance and 0.07 Henry inductance in each branch. If the load supplied with 415V at 50Hz, calculatea) the line currentb) the power factorc) the total power supplied to the load PLEASE FOLLOW THIS APPROACH TO SOLVE THE QUESTION. THANK YOUStep OneDeduce the inductive reactance.STEP TwoWrite down a rectangular expression for the impedance per branch.STEP ThreeConvert the rectangular expression into polar expression.STEP FourBecause impedance will be involved in the analysis deduce the phase voltage.STEP FiveSolve for the phase current and hence the line current.STEPVSixUse the phase angle of the current to deduce the power factor. STEP SevenFind the apparent power.
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, and admittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal place.Thank you!
(a) Calculate the equivalent impedance of the circuit given below, if the source voltage is v(t) = 60cos1000t (b) Calculate the source current flowing in the circuit (c) Draw the phasor diagram of the current and input voltage
a shunt generator supplies a load of 5,500w at 110v through a pair of feeder conductors having a resistance of 0.02 ohm each. the armature, shunt field resistances are 0.15 ohm and 50 ohms respectively, find the emf generated.