A single-phase full-wave uncontrolled bridge rectifier is supplying a highly inductive load (L/R ratio is very large), the load current is assumed to be smooth and ripple -free. If the supply voltage is 220V, 50Hz, and the inductor load resistance R=22 2, Calculate: (a) The average output voltage Vae and current Ide (b) The rms value of the output voltage Vorms and current forms. (c) The rms value of the diode current Iprms and the PRV of each diode.

A single-phase full-wave uncontrolled bridge rectifier is supplying a highly inductive load (L/R ratio is very large), the load current is assumed to be smooth and ripple -free. If the supply voltage is 220V, 50Hz, and the inductor load resistance R=22 2, Calculate: (a) The average output voltage Vae and current Ide (b) The rms value of the output voltage Vorms and current forms. (c) The rms value of the diode current Iprms and the PRV of each diode.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
A sinusoidal voltage of 48v, 60 Hz is applied to a half-wave rectifier with dynamic resistance of the diode of .001ohms turns ratio (3:1). Calculate the DC and RMS currents flowing through the load(R=210 ohms). Also calculate the dc output power developed, ac – input power supplied, rectification efficiency, and ripple factor.
A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the amplitude of the peak output voltage, Vpo appearing across the load., calculate the average DC voltage appearing across the load, calculate the DC current in mA drawn by the load.
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous
A 60-Hz full-wave rectiﬁer is built with a transformer having an rms secondary voltage of 20 V and ﬁlter capacitance C =150,000 μF. What is the largest current that can be supplied by the rectiﬁer circuit if the ripple must be less than 0.3 V?
Consider a three-phase diode rectifier supplying a R = 10 Ω DC load. The supply systemis 440 VLL and 60 Hz. A) What is the value of the average (DC) current across the load?B) Compute the value of an inductive filter (L) to be added in series with the resistiveload to limit the rms value of the lowest order current harmonic to 1% of the DC currentvalue. Note: 2 /[( 1)( 1)] Vdch = Vdc0 h − h + (in rms).
For the Zener regulated power supply a shown, the rms value of vI is 15V, the operating frequency is 60Hz, R =100Ω, C =1000μF, the on voltage of diodes D1 and D2 is 0.75V, and the Zener voltage of diode D3 is 15V.(a)What type of rectiﬁer is used in this power supply circuit?(b) What is the dc voltage at V1? (c) What is the dc output voltage VO?(d)What is the magnitude of the ripple voltage at V1? (e) What is the minimum PIV rating for the rectiﬁer diodes? (f) Draw a new version of the circuit that will produce an output voltage of−15 V.
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed to be (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply