A Spiral column is to be loaded with DL=400Kn and LL=500Kn with minimal reinforcement. The Design spiral confinement spacing is 70mm when the spiral ratio is 0.025. If the Concrete f'c = 28Mpa and Steel fy = 420Mpa, Concrete cover is 40mm and diameter of stirrups is 10mm. the Column is to be reinforced with 25mm bars. Determine the Diameter of the spiral column.

A Spiral column is to be loaded with DL=400Kn and LL=500Kn with minimal reinforcement. The Design spiral confinement spacing is 70mm when the spiral ratio is 0.025. If the Concrete f'c = 28Mpa and Steel fy = 420Mpa, Concrete cover is 40mm and diameter of stirrups is 10mm. the Column is to be reinforced with 25mm bars. Determine the Diameter of the spiral column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel barshaving fy = 414 MPa and fc’ = 21 MPa as shown in the figure. The column is to resist a factoredload of 1000 kN and factored moment of 230 kNm. Using the interactiondiagram (from the reference textbook: Reinforced Concrete Design DIT Gillesania), determine the following:a. eccentricity, eb. steel ratioc. diameter of the steel bars
A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 8-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. The centroid of the bars are 70 mm from the concrete surface. Use f’c = 21 MPa and fy = 415 MPa. 4. Determine the nominal compressive force on concrete only when the column is at balanced condition with bending about the strong axis. = [Cc] kN (whole number) Answer: 888
The column shown is strained to -0.003 on the right hand edge and to +0.002 on its left hand edge. f’c = 4000 psi and fy = 60,000 psi. determine: 1. gives the compressive force resisted by the concrete 2. gives the nominal axial load that the column could carry 3. gives the nominal flexural load that the column could carry
A rectangular column of 400mm x 600mm is subjected to an axial load of 500 kN and a moment of 30 kNm about its major axis. The grade of concrete used is M30 and the steel used is Fe415. Determine the axial load carrying capacity of the column using the limit state method.
The beam has a 20 Mpa concrete, dimensions of b=400mm, d=550 mm and reinforced with 4-25 mm diamter rebars. If it sustains a bending moment of 100 KN-m. Determine if the beam is safe using the "transformed section method". n=10
If column AB is made from high strength pre-castconcrete and reinforced with four 20 mm diameter A-36steel rods, determine the maximum allowable floorloadings P. The allowable normal stress for the highstrength concrete and the steel are (ϭallow)con = 18 MPaand (ϭallow)st= 170 MPa, respectively.
A simply supported 1 way slab having span of 3 meters is to carry the load for DL = 5kpa and LL = 4.8Kpa. If the concrete f'c = 28Mpa and rebar to be used is 10mm with fy = 276Mpa. a.) Determine the minimum thickness of the 1 way slab.(answer in millimeter in whole number) b.) Determine the Ultimate loading combination for the slab considering 1 meter strip?(answer in KN/m. in 3 decimal places ) c.) Determine the Ultimate moment for the slab considering 1 meter strip?(answer in KN-m. in 3 decimal places) d.) Determine the effective depth of the slab considering concrete cover = 20mmanswer in millimeter. in whole number e.) Determine the area of reinforcement for the slab based on the actual loadings.(answer in sq.mm. in 3 decimal places) f.) Determine the spacing of the rebar.(answer in millimeter(Don't round up, use actual value). in 3 decimal places)
A T‐beam has the following properties:Flange width, bf = 820 mmFlange thickness, t = 100 mm Width of web, bw= 250 mmEffective depth, d = 470 mm concrete strength f’c = 20.7 MPa steel strength, fy = 414 MPaDetermine the required tension steel area for the following conditions:A) MDL = 150 kN.m, MLL = 120 kN.mB) MDL = 175 kN.m, MLL = 190 kN.m
Determine the following for the given beam section: Use fc'= 25 MPa , fy=420 MPa Concrete Cover = 40 mm, Stirrups diameter= 12 mm 1. Depth of stress block, a 2. Tensile steel strain, εt, when concrete εc=0.003 3. Type of failure 4. Reduction Factor 5. Nominal Moment Capacity in kN-m 6. Ultimate Moment Capacity in kN-m
A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with 8-20-mm-diameter longitudinal bars equally distributed to the shorter sides of the column. The centroid of the bars are 70 mm from the concrete surface. Use f’c = 21 MPa and fy = 415 MPa. a. Determine the nominal compressive force on concrete only when the column is at balanced condition with bending about the strong axis. = [Cc] kN (whole number, ANS: 888) b. Determine the location of the plastic centroid from the left short side of the column. = [x] mm (ANS 200) c. Determine the ultimate axial load the column can sustain at balanced condition if the reduction factor is 0.65. = [Pub] kN (whole number, ANS 552).
A reinforced concrete spiral column carries dead axial load of 600 kN and a live axial load of 9000kN. f’c = 28 Mpa; fy = 415 Mpa. a. What is the factored axial load carried by the column? b. What is the minimum diameter of the column if it has a steel ratio of 0.015? c. Find the number of 20 mm diameter bar that will be used if it is the reinforcement of the column.
Design a one-way slab having a simple span of 3.5m. The slab is to carry a uniform live load of 4.8 kpa and uniform dead load of 6.68kN/m. Assume f'c=27.6 Mpa, fy=276 Mpa for main and temperature bars. The slab is not exposed to earth or weather. Use unit weight of concrete Yc=23.5 kN/m^3