A square block has 320 mm bottom sides dimensions, weighing W is 1.4 kN on an edge slides down an incline angle 0 is 20° on a film of oil 6 mm thickness, as shown below. Assuming a linear velocity profile in the oil. The viscosity of the oil is 0.009 Pa.s. W y Determine the force acting on the block, F. What is the velocity of the block, V?

A square block has 320 mm bottom sides dimensions, weighing W is 1.4 kN on an edge slides down an incline angle 0 is 20° on a film of oil 6 mm thickness, as shown below. Assuming a linear velocity profile in the oil. The viscosity of the oil is 0.009 Pa.s. W y Determine the force acting on the block, F. What is the velocity of the block, V?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

A differential equation is d2ydt2=Ay2+Byt where y represents a distance and t is time. Determine the dimensions of constants A and B for which the equation will be dimensionally homogeneous.
In Fig. both fluids are at 20 ° C. If surface tensioneffects are negligible, what is the density of the oil,in kg/m 3 ?
Please answer only when you are sure and give correct answer Thedensity of an oil at 23°C is 750kg / (m ^ 3) Find its relative density and kinematic viscosity if the dynamic viscosity is 5 * 10 ^ - 3 * kg / m * s .
A flat area 1.5x106mm² is pulled with a speed of 0.4m/s relative to another plate located at a distance of 0.15mm from it. Find the force and power required to maintain this speed, if the fluid separating them is having viscosity as 1 poise.
A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN
A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in throughnarrow gap of length, L as depicted in Figure 2. Following below values are given:c = 0.300 mm, t = 0.381 mm, and L = 20.0 mm.The lubricant, of dynamic viscosity  = 1.0054 kg/m.s completelys fills the gap and the velocitydistribution is asssumed to linear as shown in Figure 2. The maximum allowable force in tape isgiven as F = 30.04 N. Find the maximum allowable tape speed
An oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high. Find the minimum push required at the top of the drum. Take density of the oil as 1 kg/litre. Neglect weight of the drum.
an oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high.find the minimum push required at the top of the drum.take density of the oil as 1kg/litre.neglect weight of the drum.
27. The space between two square flat parallel plates is filled with oil. Each side of the plate is 560 mm. the thickness of the oil film is 10 mm, the upper plate, which moves at 2.8 m/s requires a force of 92 N to maintain the speed. Determine a) the dynamic viscosity of oil in poise, b) the kinematic viscosity of the oil in stokes if the specific gravity of the oil is 0.75. And also draw the neat sketch. i) Dynamic viscosity of oil =________________ Poise. ii) Kinematic viscosity of oil =__________________ Stokes.
We are willing to design a simple setup for the lubrication of a rotating rod. To do so, the vertically aligned rotatingrod is approached to a horizontal surface that is covered with oil. The rod approaches the surface, so there is a 0.2 mmof liquid film between the rod and the fixed surface. Suppose that the radius of the rod is 15 mm, and the rod's angularvelocity is 1500 rpm. Determine the power consumption due to the friction.
Estimate the density of a 0.8-specific gravity dead oil at 40 C
A solid cone of angle 2θ, mass (m), base radius (r0), and density (ρc), is rotating with angular velocity (w0) on its conical seat. The clearance (h) is filled with oil of viscosity (μ). Neglecting air resistance, determine: a) an expression for the moment (M) as a function of r0, w0,μ,θ, and h. b) an expression for the angular velocity (w) for t≥0 as a function of w0,μ,θ,h, r0,m and t if an external torque is not applied. If the radius of gyration of the cone is 16 cm, determine: c ) the value of the angular momentum and velocity if w0=60RPM,h=0.05mm,θ=30°,μ=0.98cPoise , m=20kg, t=2.0s