1. The deformation of the fluid will continue as long as theis applied.2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important notonly to estimate thebut also to specify its location on the body.3. The surface tension is the tensile force perin any direction along the surface the surface tension.4. The value of ---------- s pecifies whether the fluid can be assumed compressible or incompressible.5. Archimedes' principle indicates6. A truck is filled with gasoline. If the container (tank) on the truck undergoes athen the liquidsurface will begin to rotate clockwise about the center of the container and will eventually maintain afixed tilted position.

Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

1. The deformation of the fluid will continue as long as the is applied. 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the 3. The surface tension is the tensile force per but also to specify its location on the body. in any direction along the surface the surface tension.

1. The deformation of the fluid will continue as long as the is applied. 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the 3. The surface tension is the tensile force per but also to specify its location on the body. in any direction along the surface the surface tension.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.35P: The weight of the cylindrical tank is negligible in comparison to the weight of water it contains...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.
A differential equation is d2ydt2=Ay2+Byt where y represents a distance and t is time. Determine the dimensions of constants A and B for which the equation will be dimensionally homogeneous.
Compute the surface area of the axi-symmetric domed structure.
The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
Determine the dimensions of constants A and B far which the following equation is dimensionally homogeneous: F=Akx2sinBxk where F is a force, x is a distance, and k represents stiffness (dimensions: [FL1]).
An oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high. Find the minimum push required at the top of the drum. Take density of the oil as 1 kg/litre. Neglect weight of the drum. [Ans. 1444.5 N]
The gage pressure of air in a pressurized water tank is measured simultaneously by both a pressuregage and a manometer. The differential height h of the mercury column is to be determined. Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible dueto its low density), and thus the pressure at the air-water interface is the same as the indicated gagepressure.
Q1 Determine the minimum size of glass tubing that can be used to measure water level, if the capillary rise in the tube is not to exceed 0.3 mm. Take surface tension of water in contact with air as 0.0735 N/m. A U-tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. Q2) The tube is held vertical and partially filled liquid of surface tension 0.06 N/m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the density the liquid. Q10) In measuring the unit energy of a mineral oil (specific gravity = 0.85) by the bubble method, a tube having an internal diameter of 1.5 mm is immersed to depth of 12.5 mm in oil. Air is forced through the tube forming a bubble at the lower end. What magnitude of the unit surface energy will be indicated by a maximum bubble pressure intensity of 150 N/m.
1. The height of the manometer depends on the _______ of the manometric fluid.2. _______ gives the interaction between the pressure acting at a point on the surface of the liquidand velocity of its particle. It states that the total energy of a small amount of an incompressibleliquid flowing from one point to another remains constant throughout the displacement.3. _______ states that the buoyant force or up thrust experience by an object immersed in a liquidis equal to the weight of the liquid displaced.4. The upward force experienced by a body when partially or wholly immersed in a fluid iscalled _______.5. _______ states that the velocity of the fluid through an orifice is equal to that which a body wouldattain in falling freely from the free surface of the liquid to the orifice.6. A floating body is known to be _______ when the metacentric height is above the center ofgravity.
Water at 25° is flowing between A and B through a steel pipe 30 centimeters in diameter and a lengthof 47m. Point B is 10 meters above A and thepressure at B must be maintained at 1.4 kg/cm2. If 220 It/s circulate through the pipe, what pressure must exist in A?
Capillary rise in the glass tube used for measuring water level isnot to exceed 0.5 mm. Determine its minimum size, given thatsurface tension for water in contact with air = 0.07112 N/m.