A square footing placed at a depth of 1 m is required to carry a load of 1000 kN. Find the required size of footing given the following data. C = 10 kPa, ϕ = 38o, γ = 19 kN/m3, Nc = 61.35, Nq = 48.93, Nγ= 74.03 and  F = 3.Assume water table is at the base of footing.

Q: What is the meaning of the term "scope?"

A: The term scope describes the total set of goals and demands necessary to finish a project.

Q: Design CBR value of subgrade Initial traffic on completion of construction = 300 commercial vehicles…

A:

Q: A concrete sidewalk is constructed between two buildings on a day when the temperature is 25 C. The…

A: Length of single sidewalk(L)=3m To find vertical displacement in the slab

Q: Q5) Determine the reactions at the supports. Ion I -6 ft- 5k/ft 12 ft $30 6 ft B

A:

Q: The beam is used to support a dead load of 1 kN/m, a live load of 5 kN/m, and a concentrated live…

A: Given-The beam is used to support a dead load of 1 kN/m, a live load of 5 kN/m, and a concentrated…

Q: PROBLEM TO SOLVE: 600 mm 400 mm Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: a.…

A:

Q: 3. Given the crest vertical curve below, a. Determine the elevation of BVC and EVC, compute also for…

A:

Q: 7. 1m 12KN/m I 5m 9KN/m 21 6m

A:

Q: Principal criteria in designing highway. Explain each criteria.

A: There are many factors that influence designing a highway. Appropriate analysis of traffic…

Q: The drag force, Fa, imposed by the surrounding air on a vehicle moving with velocity Vis given by…

A:

Q: The following offsets, with 15m interval were measured at right angles from a traverse line to…

A:

Q: The theoretical density and bulk density of a bituminous mix are 2.48 gm/cm³ and 2.39 gm/cm³,…

A:

Q: Determine the force in members GF, GD, and CD of the truss. State if the members are in tension or…

A:

Q: Problem 5 A strip footing shown has an inclined load acting at an eccentricity shown. Cohesion = 18…

A:

Q: TABLE 1 LINE 1-2 2-3 3-4 4-5 5-1 TABLE 2 LINE 1-2 2-3 3-4 4-5 5-1 FORWARD BEARING S 38° 39' W N…

A:

Q: The base width of a solid gravity dam is 35 m and the specific gravity of dan material is 2,45. What…

A:

Q: Q- The levelling staff held at a distance of 200 m is read at 4.54 m with the bubble out of centre…

A: Given data- Distance D=200 m, No. of divisions n=2, Sensitiveness- α=25, Staff reading SR=4.54 m. To…

Q: Solve the reactions at the supports. T 8 ft 50 k 16 ft 1 A FURETTY NIESN -12A36 ft- Hinge 125 k B 14…

A: its very  easy  questions   you just have to calculate  the moment  about critical points like A,B…

Q: 5/101 Determine the reactions at A and B for the beam subjected to a combination of distributed and…

A: Using equilibrium equation

Q: A cohesive soil has an angle of shearing of 30 and a cohesion of 35 kN/m2. If the specimen this soil…

A: Given- A cohesive soil, Angle of shearing- ϕ=30o, cohesion C= 35 kN/m2, Triaxial compression test-…

Q: 3-Following are the results of consolidated-undrained triaxial tests on undisturbed soils: Confining…

A: Given, Consolidation undrained test data    To find, Shear strength parameters (c' and ϕ')

Q: A 76 mm x 76 mm x 6 mm angular section is welded to a gusset plate having a thickness of 10 mm as…

A: Given data: Agross=929 mm2Fy=248 MPaFu=400 MPa

Q: Derive the stopping sight distance (SSD) formula as shown: where V t f G d₂ SSD = d₂ + d₂ vt 3.6 d₁…

A: Stopping sight distance is minimum distance that must be available in front of driver so that he can…

Q: For the beam below, (a) draw the shear and moment diagrams and (b) determine the maximum norr stress…

A: Given Fig : TO Find : a) Determine the shear and bending diagram  b) Determine the max. normal…

Q: A bridge has an expected life of 25 years and is designed for a flood magnitude of return period 100…

A: Risk = The probability of a flood to occur at least once in n successive years Risk = 1 – qn = 1 –…

Q: A beam is loaded as show in the figure. Assume EI is constant. Using Virtual Work Method determine…

A:

Q: A sub-marine which may be supposed to approximate a cylinder 4m in diameter and 20m long travels…

A: Given: Diameter of cylinder D= 4 m, Length of cylinder L=20 m, Velocity of cylinder U=1.3m/s,…

Q: Situation 5 A well of diameter 300 mm is constructed to the full depth of a soil of thickness 150 m,…

A: As per bartleby guidelines. We have to solve 1st question in case of multiple question. Please…

Q: Use slope deflection method or three moment equation. Draw the shear & moment diagram. UDL SPAN UP…

A: Given: Required : Analyze the beam using slope deflection method and draw shear force and bending…

Q: 1 kN/m, a live load of 2 kN/m, and a concentrated live load of 52 kN. Determine the following:…

A:

Q: In a 5 m wide rectangular channel, the velocity u distribution in the vertical direction y is given…

A:

Q: Q2: A is 4500 m length-gas flow line, and B is 2000 m length-liquid flow line (0.1 m diameter) both…

A: Given:-L=2000mleft side length=2500mmPressure at A - pipe line inlet=2400kPaPressure at C pipe line…

Q: The results of a constant-head permeability test for a sand sample having a sectional area of…

A: Using Darcy's law

Q: Consider the beam and loading shown in the figure below. The beam has a flexural rigidity of El over…

A:

Q: specific gravity of solids as 2,68 and mass specific gravity 1.80, the void ratio of the soil sample…

A:

Q: The beam is used to support a dead load of C kN/m, a live load of A kN/m and a concentrated live…

A: "Since you have posted a person with  multiple subparts. we will solve first three for you. To get…

Q: solve the indeterminate structure using moment distribution method

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Since, it is a cantilever truss and in this case we do not need to find the support reactions.Sign…

Q: The number of impellers required for a multistage pump to lift 4500 litres/minute against a total…

A: Given- Discharge- Q=4500 litres/minute,total head H=190 m,Speed N=750 rpm,specific speed Ns=700. It…

Q: *6-84. Determine the force that the smooth 20-kg cylinde exerts on members AB and CDB. Also, what…

A:

Q: Find the forces produced in Bars 1, 2, and 3 of the truss shown due to the action of a ball of…

A: FE is parallel to AC

Q: Solve all support reactions using the Method of Consistent Deformation. Consider B as the redundant.

A: In the method of consistent deformation, we use both equilibrium and compatibility equations to…

Q: A wall is 2.5 m high and 6m long consists of 200 mm clay bricks with 50mm x 100mm plastered wood…

A: Giventhat Wall is 2.5m high  Length= 6m  Consists 200mm clay bricks and 50×100 plastered wood studs…

Q: Determine the determinacy of the given figure. Determine the reaction at A, B, C, D, and E. The…

A:

Q: The beam is used to support a dead load of C kN/m, a live load of A kN/m and a concentrated live…

A:

Q: 8 mm- 8 mm 250 mm 8 mm steel beam has the cross-sectional area shown. The beam is loaded as shown…

A: Given : w  = 70 kN/m Determine the absolute max. bending stress ?

Q: b) Solve for the forces in each of the members. (the reaction forces are shown) 4,000 N

A: Given :

Q: Problem- Find the surface tension in a soap bubble of 50 mm diameter with its inside pressure being…

A: Given data: Soap bubble diameter, d=50 mm=50×10-3 m Inside pressure, P = 2.5 N/m2

Q: 7. For the given force system shown in figure 2, if force P=50kn, determine the magnitude and…

A:

Q: In a traffic safety study to reduce pedestrian-vehicle accidents on a level road segment, it was…

A: Given data, Distance traveled by the vehicle before hitting the pedestrian = 60m The initial speed…

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.