A square high-density polyethylene [a = 158x10-6/°C] plate has a width of 215 mm. A 129 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 47°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole. Part 1 Calculate the thermal strain. Answer: ET = i με

A square high-density polyethylene [a = 158x10-6/°C] plate has a width of 215 mm. A 129 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 47°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole. Part 1 Calculate the thermal strain. Answer: ET = i με

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.7P: A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the...

See similar textbooks

Similar questions

A square high-density polyethylene [α = 158×10–6/°C] plate has a width of 205 mm. A 123 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 45°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole.
A square high-density polyethylene [α = 158×10–6/°C] plate has a width of 250 mm. A 150 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 37°C, determine:
A steel rod, which is free to move, has a length of 200 mm and a diameter of 20 mm at a temperature of 15oC. If the rod is heated uniformly to 115oC, determine the length and diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10-6 m/m/C. Is there a stress on the rod at 115oC?
Determine the notch sensitivity for the specimen whose maximum stress in notched specimen is 250 MPa and stress in notch free specimen is 100 MPa . The theoretical stress concentration factor is given as 3. A) 0.75 B) 0.80 C) 1.2 D) 0.5
The jet plane is flying upward such that its wings make an angle of attack of 15∘∘ with the horizontal. The plane is traveling at V� = 750 m/sm/s , in air having a temperature of 8∘C∘C and absolute pressure of 95 kPakPa . The leading edge of the wing has an angle of 8∘∘. (Figure 1) Express your answer to three significant figures and include the appropriate units. Determine the temperature of the air just in front or to the right of the expansion waves. Express your answer using three significant figures.
The rod A has a cross sectional area 2376 mm2, modulus of elasticity 68 Gpa and thermal expansion coefficient 0.000022 1 / C . The rod B has a cross sectional area 874 mm2, modulus of elasticity 176 Gpa and thermal expansion coefficient 0.000019 1 / C . When the temperature T1=24 C a 0.5 mm gap exists between the ends of the rods. If the temperature T2=182 C. Answer the following questions:
Determine the bulk modulus of elasticity of a fluid which is compressed in a cylinder from a volume o 0.009 m at 70 N/cm pressure to a volume of 0.0085 m² at 270 N/cm pressure.
Is the material homogeneous and isotropic? How does it behave?
A water tank is completely filled with liquid water at 60°C. The tank material is suchthat it can withstand tension caused by a volume expansion of 4%. Determine the maximum temperature rise allowed without jeopardizing safety. Take water coefficient of expansion (β) as 5.22 x 10-4 1/K at this temperature.
A thermometer is being designed for a process in which the temperature varies from 0 to 180 °C; from experience it is known that the process temperature, when it gets out of control, reaches up to 240 ° C. Considering that only the bulb is in contact with the part inside the equipment, what should be the volume of the safety vial? It is known that the bulb has a length of 1.2 cm and a diameter of 0.5 cm; the capillary has a length of 20 cm and the scale of the thermometer is -10 to 190 ° C. Consider that the coefficient of volumetric expansion for mercury is 1.82×10−4 ° C− 1
A 601.7 mL sample of oil is subjected to a pressure increase of 9.2 MPa due to a piston, which causes the volume occupied by the oil to decrease to 585.1 mL. Determine the volumetric modulus of the oil in question. Result in scientific notation
A 601.7 mL sample of oil is subjected to a pressure increase of 9.2 MPa due to a piston, which causes the volume occupied by the oil to decrease to 585.1 mL. Determine the volumetric modulus of the oil in question.