A steam power plant operates according to the regenerative Rankine cycle with one feed water heater. The steam is delivered to the turbine at a boiler pressure of 3 MPa and a temperature of 350 °C, while the condenser is kept at a pressure of 5 kPa. Draw a T-s-diagram to illustrate the regenerative process, neglect feed pump work and calculate: The intermediate pressure at which the steam is bled off (use the average value of the temperature to determine the required pressure). The mass fraction of steam being bled off, and The Rankine efficiency.

A steam power plant operates according to the regenerative Rankine cycle with one feed water heater. The steam is delivered to the turbine at a boiler pressure of 3 MPa and a temperature of 350 °C, while the condenser is kept at a pressure of 5 kPa. Draw a T-s-diagram to illustrate the regenerative process, neglect feed pump work and calculate: The intermediate pressure at which the steam is bled off (use the average value of the temperature to determine the required pressure). The mass fraction of steam being bled off, and The Rankine efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 623 K and is condensed in the condenser at a pressure of 10 kPa. Determine (i) the thermal efficiency of this power plant, (ii) the thermal efficiency if steam is superheated to 873 K instead of 623 K, and (iii) the thermal efficiency if the boiler pressure is raised to 15 MPa while the turbine inlet temperature is maintained at 873 K.
A simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 40C and its boiler at 300C. Calculate the work produced by the turbine, the heat supplied in the boiler, and the thermal efficiency of this cycle when the steam enters the turbine without any superheating.
A steam power plant operating on a simple ideal Rankine cycle maintains the boiler at 6000 kPa, the turbine inlet at 600C, and the condenser at 50 kPa. Compare the thermal efficiency of this cycle when it is operated so that the liquid enters the pump as a saturated liquid against that when the liquid enters the pump 11.3C cooler than a saturated liquid at the condenser pressure.
Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 10 kPa. Determine the thermal efficiency of this power plant, the thermal efficiency if steam is superheated to 600°C instead of 350°C, and the thermal efficiency if the boiler pressure is raised to 15 MPa while the turbine inlet temperature is maintained at 600°C. Draw the T-S diagram of each condition.
A steam power plant operates on the simple ideal Rankine cycle. The steam enters the turbine at 4 MPa and 500°C and is condensed in the condenser at a temperature of 40°C. draw and label the schematic diagram and the pV and TS planes. (a) Show the cycle on a T-s diagram. If the mass flow rate is 10 kg/s, determine (b) the thermal efficiency of the cycle (c) the net power output in kW.
A steam power plant operates on an ideal regenerative Rankine cycle with two open feedwater heaters. Steam enters the turbine at 10 MPa and 600C and exhaust to the condenser at 5 kPa. Steam is extracted from the turbine at 0.6 and 0.2 MPa. Water leaves both feedwater heaters as a saturated liquid. The mass flow rate of steam through the boiler is 22 kg/sec. Show the cycle on a T-s diagram, and determine (a) Total power requirement of the pump in Hp, (b) Turbine power output in MW, (c) the net power output of the power plant in MW, (d) mass of steam extracted for feedwater heating in kg/sec,
Consider a steam power plant that operates on a simple ideal Rankine cycle and has a net power output of 45MW. Steam enters the turbine at 7 MPa and 500 ˚C and is cooled in the condenser at a pressure of 10kPa by running cooling water from a lake through the tubes of the condenser at a rate of 2000 kg/s. Show the schematic diagram of the power plant and draw the cycle on a T-s diagram with respect to saturation lines. Also, determine (a) the thermal efficiency of the cycle, (b) the mass flow rate of the steam, and (c) the rise in temperature of the cooling water. Repeat your calculations assuming an isentropic efficiency of 85 and 90 for the turbine and the pump, respectively.
Consider a steam power plant that operates on an ideal regenerative Rankine cycle and has a net power output of 150 MW. Steam enters the turbine at 10 MPa and 500°C and the condenser at 15 kPa. Steam is extracted from the turbine at 0.5 MPa to heat the feedwater in an open feedwater heater. Water leaves the feedwater heater as a saturated liquid. Show the cycle on a T-s diagram, and determine (a) the mass flow rate of steam through the boiler, and (b) the thermal efficiency of the cycle.
1. What is the Isentropic Work of the Steam using the Ideal Rankine Cycle when the system is set at 400 kPaa Boiler Pressure and 105 kPaa Condenser Pressure when the system is generating power at 9,500 seconds? 2. With the Turbine work output, what is the Isentropic efficiency of the Turbine from the above settings?
Consider a power plant operating on a Rankine cycle using steam as the working fluid. The boiler pressure is 2500 kPa and the steam leaving the boiler is superheated to a temperature 126 ◦ C above its saturation temperature. The condenser temperature is 50 ◦ C and it discharges saturated liquid. The eﬃciency of the turbine is 0.90 and of the pump 0.80 as compared to reversible and adiabatic equipment operating at the same pressure ranges. a) Sketch the cycle on a T -S diagram. b) Calculate the thermal eﬃciency of the cycle. c) Compare the thermal eﬃciency of this Rankine cycle with the thermal eﬃciency of a Carnot cycle receiving heat at the saturation temperature of steam at 2500 kPa and discarding it at 50 ◦
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of 1250 and 2 psia. The mass flow rate of steam through the cycle is 75 lbm/s. The moisture content of the steam at the turbine exit is not to exceed 10 percent. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the minimum turbine inlet temperature, (b) the rate of heat input in the boiler, and (c) the thermal efficiency of the Cycle. Answers:
A steam power plant operates on a simple ideal Rankine cycle between the pressure limits of 1250 and 2 psia. The mass flow rate of steam through the cycle is 75 lbm/s. The moisture content of the steam at the turbine exit is not to exceed 10 percent. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the minimum turbine inlet temperature, (b) the rate of heat input in the boiler, and (c) the thermal efficiency of the cycle.