A steam power plant operates on a cycle for the following conditions. Determine (a) steam rate (b) heat transfer rate in boiler (c) heat transfer rate in the condenser (d) thermal efficiency of the plant. P1 = P4 = 7000 kPa, T1 = 550°C, P2 = P3 = 20 kPa, ŋT = 0.75, np = 0 75 PT = 100 000 kW.

A steam power plant operates on a cycle for the following conditions. Determine (a) steam rate (b) heat transfer rate in boiler (c) heat transfer rate in the condenser (d) thermal efficiency of the plant. P1 = P4 = 7000 kPa, T1 = 550°C, P2 = P3 = 20 kPa, ŋT = 0.75, np = 0 75 PT = 100 000 kW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refrigerator 1 simulates an ideal refrigerator and therefore operates on a Carnot cycle using R-134a as the refrigerant at a flow rate of 1.4 kg/sec. The condensing and evaporating temperatures are 30 °C and -10 °C, respectively. To assess the performance of Refrigerator 1, you must submit the report. of the project with the following information: d) The work generated by the turbine; e) The condenser heat rejection rate (Q H); f) The coefficient of performance of the cycle.
A steam-powered power plant works on the basic Rankine cycle.shown in the figure. Likewise, some of its thermodynamic states are summarized in the attached table.Knowing that the work per unit mass delivered to the pump is 3W4 = 2480 (J/kg], determinein SI units the following: a) The specific volume of water in state 4.b) The associated work per unit mass, developed in the Curbina.c) The associated heat per unit mass released by the water in the condenser.d) The efficiency of the cycle
Refrigerant-134a enters the compressor of a refrigerator as superheated vapor at 0.22 MPa and 27 C at a rate of 0.07 kg/s, and it leaves at 1.2 MPa and 73°C. The refrigerant is cooled in the condenser to 44°C and 1.16 MPa, and t is throttied to 0.21 MPa. Disregarding any heat transfer and pressure drops in the connecting lines between the components, show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the rate of heat removal from the refrigerated space and the power input to the compressor, (b) the isentropic efficiency of the compressor, and (c) the COP of the refrigerator.
A Rankine-cycle steam power plant has a 5-MPa/450°C throttle and 10-kPa condenser pressure . the generator produces 19 MW at an efficiency of 95% and mechanical efficiency of 96%. The actual expansion of the turbine is 85%. a.)Determine the ideal engine heat rate in kj/kWh. b.) Determine the indicated power in kW. c.) Determine the ideal cycle steam rate in kg/kWh. d.) determine the theoretical engine thermal efficiency in %. e.) determine the mass flow rate of steam in kg/s. f.) determine the ideal wok of the turbine in kj/kg. g.)Determine the theoretical cycle thermal efficiency in %.
A steam-powered power plant works on the basic Rankine cycle.shown in the figure. Likewise, some of its thermodynamic states are summarized in the attached table.Knowing that the work per unit mass delivered to the pump is ›W = 2480 (J/kg], determinein SI units the following: a) The specific volume of water in state 4.b) The associated work per unit mass, developed in the Curbina.c) The associated heat per unit mass released by the water in the condenser.d) The efficiency of the cycle
Steam turbine receives steam at 9.5 MPa, 540°C and the condenser at 0.01 MPa. Steam are extracted at 3 MPa, 1.8 MPa, and 0.6 MPa. Determine the following: 1. Degree superheat at point 2 2. Quality of steam at point 4 3. Mass extracted in kg/hr for each feedwater open heater and the remaining mass that enters the condenser assuming 20,000 kg/hr of throttle flow 4. Work net in kW 5. Cycle thermal efficiency
A 1000-MW supercritical double-reheat steam power plant operates withthe main (live) steam condition of 250 bars and 560°C and the condenserpressure of 0.04 bar. The steam is reheated first at 30 bars to 560°C andthen at 4 bars to 560°C. The turbine efficiency is 0.92. The feed pumpwork may be ignored. Calculate: (a) the plant net specific work, (b) the plant thermal efficiency, (c) the plant steam mass flow rate, and (d) the plant heat rate.
Refrigerant-134a enters the condenser of a steadyflow Carnot refrigerator as a saturated vapor at 90 psia, and it leaves with a quality of 0.05. The heat absorption from the refrigerated space takes place at a pressure of 30 psia. Show the cycle on a T-s diagram relative to saturation lines, and determine (a) the coefficient of performance, (b) the quality at the beginning of the heat-absorption process, and (c) the net work input.
2. A steam power plant operates on the Rankine cycle in which the steam enters the turbine at 16 MPa and 600°C and the condensate leaves the condenser at 10 kPa. If the isentropic efficiency of the turbine is 87 percent and the isentropic efficiency of the pump is 85 percent, determine (a) the thermal efficiency of the cycle and (b) the net power output of the plant for a mass flow rate of 15 kg/s.
Refrigerant 134a is the working fluid in a solar power plant operating on a Rankine cycle. Saturated vapor at 60 degree Celsius enters the turbine, and the condenser operates at a pressure of 6 bar. The rate of energy input to the collectors from solar radiation is 0.4 kW per m2 of collector surface area. Determine the minimum possible solar collector surface area, in m2, per kW of power developed by the plant.
Refrigerant R134a is a working fluid in an ideal vapor-compression refrigeration cycle that communicate thermally with a cold region at 0 °C and a warm region at 26 °C. The fluid enters the compressor at 0 °C andleaves condenser at 26 °C. the mass flow rate of the refrigerant is 0.08 kg/s.Evaluate;i.the compressor powerii.The heat transfer of refrigerant andiii.Coefficient of performance, COP.iv.Compareand explainthe results above if the temperature of the cold region of refrigerant is -10 °C and pressure of condenser is 9 bar?
In a steam power plant that operates based on a Rankine cycle, the operating pressures of the steam generator and the condenser are 10,000 and 10 kPa, respectively. If the turbine inlet stream is saturated vapor and the condenser outlet flow is saturated liquid, determine the specific heat transfers in the steam generator and the condenser, the specific work involved in the turbine and the pump, and the thermal efficiency and the BWR of the cycle. Also, if the power plant produces 250 MW power, determine the mass flow rate of the cycle’s working fluid.