A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 6 MPa and 20 kPa. Steam enters the high pressure turbine at (b) 6 MPa and leaves at 2 MPa. Steam is then reheated at constant pressure to same temperature. Heat is transferred to the steam in the boiler at a rate of 58,416 kJ/s. And the mass flow rate of steam through the cycle is 20 kg/s. The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 8 per cent. Steam is cooled in the condenser by the cooling water from a nearby river, and the temperature rise is 12°C. Show the cycle on a T-s diagram with respect to saturation lines, and determine; i. the turbine inlet temperature; ii. the net power output and thermal efficiency; and ii the minimum mass flow rate of the cooling water required

A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 6 MPa and 20 kPa. Steam enters the high pressure turbine at (b) 6 MPa and leaves at 2 MPa. Steam is then reheated at constant pressure to same temperature. Heat is transferred to the steam in the boiler at a rate of 58,416 kJ/s. And the mass flow rate of steam through the cycle is 20 kg/s. The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 8 per cent. Steam is cooled in the condenser by the cooling water from a nearby river, and the temperature rise is 12°C. Show the cycle on a T-s diagram with respect to saturation lines, and determine; i. the turbine inlet temperature; ii. the net power output and thermal efficiency; and ii the minimum mass flow rate of the cooling water required

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas-turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1200 kPa. The working fluid is air, which enters the compressor at 30°C at a rate of 150 m3/min and leaves the turbine at 500°C. Using constant specific heats for air and assuming a compressor isentropic efficiency of 82 percent and a turbine isentropic efficiency of 88 percent, determine (a) the net power output, (b) the work ratio, and (c) the thermal efficiency.
Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5400 kPa, the reheat section 1100 kPa, and the condenser at 10 kPa. The mixture quality at the exit of both turbines is 94 %. Determine the following values. (1) The specific enthalpy at the exit of the high-pressure turbine. (2) The specific entropy at the exit of the high-pressure turbine. (3) The temperature at the inlet of the high-pressure turbine. (4) The temperature at the inlet of the low-pressure turbine. (5) The thermal efficiency of the cycle.
A gas-turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1600 kPa. The working fluid is air, which enters the compressor at 40°C at a rate of 850 m3 /min and leaves the turbine at 650°C. Assuming a compressor isentropic efficiency of 85 percent and a turbine isentropic efficiency of 88 percent, determine the back work ratio.
The second steam power plant operates on a regenerative Rankine cycle, where water is used as the working fluid. Steam enters the turbine at 8 MPa and 450 ºC. After isentropic expansion in the first stage of the turbine, steam is extracted at an intermediate pressure of 0.75 MPa and passed to a closed feedwater heater. The feedwater leaves the heater at 8 MPa and a temperature equal to the saturation temperature at 0.75 MPa. The saturated liquid condensate from the feedwater heater leaves at 0.75 MPa and is pumped into the feedwater line. The condenser pressure is 7.5 kPa. The net power output from the cycle is 100 MW Task 41. Draw the TS diagram for this system and clearly label all the states2. Find the rate of heat transfer to the working fluid passing through the steam generator.3. Determine the thermal efficiency of the cycle.4. Explain how the turbine work output, heat supplied, heat rejected and moisture content at turbine exit change when regeneration is added to a simple ideal…
Steam enters the high-pressure turbine of a steam power plant that operates on the reheat Rankine cycle at 10 MPa and 550°C and leaves at 4 MPa. Steam is then reheated to 500°C before it expands to a pressure of 40 kPa. The enthalpy of steam is 3190 kJ/kg at the exit of the high-pressure turbine, and 2550 kJ/kg at the exit of the low-pressure turbine. Disregarding the pump work, the cycle efficiency is
A gas-turbine power plant operates on the simple Brayton cycle between the pressure limits of 100 and 1600 kPa. The working fluid is air, which enters the compressor at 40°C at a rate of 850 m3 /min and leaves the turbine at 650°C. Assuming a compressor isentropic efficiency of 85 percent and a turbine isentropic efficiency of 88 percent, determine the net power output.
A steam power plant operates on an ideal Rankine cycle with two stages of reheat and has a net power output of 75 MW. Steam enters all three stages of the turbine at 550C. The maximum pressure in the cycle is 10 MPa, and the minimum pressure is 30 kPa. Steam is reheated at 4 MPa the first time and at 2 MPa the second time. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the thermal efficiency of the cycle, and (b) the mass flow rate of the steam.
A steam power plant operates on an ideal regenerative Rankine cycle with two open feedwater heaters. Steam enters the turbine at 10 MPa and 600C and exhaust to the condenser at 5 kPa. Steam is extracted from the turbine at 0.6 and 0.2 MPa. Water leaves both feedwater heaters as a saturated liquid. The mass flow rate of steam through the boiler is 22 kg/sec. Show the cycle on a T-s diagram, and determine (a) Total power requirement of the pump in Hp, (b) Turbine power output in MW, (c) the net power output of the power plant in MW, (d) mass of steam extracted for feedwater heating in kg/sec,
A gas-turbine power plant operates on the simple Brayton cycle between the pressure limits of 200 and 1500 kpa. The working fluid as air, which enters the compressor at 30C at a rate of 20 kg/s and enters at the turbine at 900k. Using variable specific heats for air and assuming a compressor isoentropic afficiency of 90 % and a turbine isentropic efficiency of 100%, determine a) the net power output, b) the back work ratio, and c) the thermal efficiency
A steam power plant operates on an ideal regenerative Rankine cycle with two open feedwater heaters. Steam enters the turbine at 8 MPa and 550C and exhausts to the condenser at 10 kPa. Steam is extracted from the turbine at 0.6 and 0.2 MPa. Water leaves both feedwater heaters as a saturated liquid. The mass flow rate of steam through the boiler is 16 kg/s. Show the cycle on a T-s diagram, and determine (a) the net power output of the power plant and (b) the thermal efficiency of the cycle.
A steam power plant operates on an ideal reheat Rankine cycle between the pressure limits of 14 MPa and 10 kPa. The mass flow rate of steam through the cycle is 10 kg/s. Steam enters both stages of the turbine at 500°C. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed 12 percent, determine (a) the pressure at which reheating takes place, (b) the total rate of heat input in the boiler, and (c) the thermal efficiency of the cycle. Also, show the cycle on a T-s diagram with respect to saturation lines.
Consider a steam power plant that operates on an ideal regenerative Rankine cycle and has a net power output of 150 MW. Steam enters the turbine at 10 MPa and 500°C and the condenser at 15 kPa. Steam is extracted from the turbine at 0.5 MPa to heat the feedwater in an open feedwater heater. Water leaves the feedwater heater as a saturated liquid. Show the cycle on a T-s diagram, and determine (a) the mass flow rate of steam through the boiler, and (b) the thermal efficiency of the cycle.