Q2/ Four pipes A, B, C, and D form a system of pipes that connects two reservoirs A and B, as shown in figure below. The pipe properties are given in table below. The water surface levels of the reservoirs A and B are 100m and 80m, respectively. Neglect the minor losses. Determine the flow rate in each pipe of the system. Take f-0.02.

Q2/ Four pipes A, B, C, and D form a system of pipes that connects two reservoirs A and B, as shown in figure below. The pipe properties are given in table below. The water surface levels of the reservoirs A and B are 100m and 80m, respectively. Neglect the minor losses. Determine the flow rate in each pipe of the system. Take f-0.02.

Name: Q2/ Four pipes A, B, C, and D form a system of pipes that connects tw
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2/ Four pipes A, B, C, and D form a system of pipes that connects tworeservoirs A and B, as shown in figure below. The pipe propertiesare given in table below. The water surface levels of the reservoirsA and B are 100m and 80m, respectively. Neglec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and then is suddenly reduced to 50 mm for the next 9 m. The difference of levels between the tank water levels is 2.40 m. Pipe coefficient f=0.005 and the contraction coefficient at sudden change in area is 0.58. Find all the losses, in terms of velocity v2 at exit from the 50 mm2pipe and hence find rate of flow. Draw the Hydraulic gradient line.
A 2-inch diameter hose is conveying water at a flow rate of 20 gpm from point A to point B. The pressure at point A is 40 psi. The elevation at point A is 20 ft above mean sea level (MSL) and the elevation at point B is 18.5 ft above MSL. The hose is 100 ft long. Determine (a) pressure at point B if there is no head loss, (b) pressure at point B if head loss is 1 inch per foot of pipe length. (c) Compare pressure at B with and without headloss - what impact does head loss have?
C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm diameter pipe at the rate of 102 liters/s and throat diameter is 98 mm. The entrance and throat of the venturimeter are connected in the two limbs of a U-tube mercury manometer. The difference in mercury level shows 835 mm. Calculate (i) the head difference in m of oil, (ii) the theoretical discharge in m3/s, (iii) the actual discharge in m3/s, and (iv) the coefficient of discharge of a venturimeter. If instead of a U-tube mercury manometer, the pressure gauges are inserted at the entrance and throat of venturimeter. Find (v) the pressure at the throat in N/mm2, if the entrance pressure gauge shows0.126 N/mm2. (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) (i) the head difference in m of oil (ii) the theoretical discharge in m3/s (iii) the actual discharge in m3/s (iv) the coefficient of…
Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. UNKNOWN: DIAMETER OF THE PIPE STRICTLY SHOW COMPLETE FBD AND SOLUTION MUST BE HANDWRITTEN
In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head loss at discharge in meters c. Total head losses in meters d. Total dynamic head developed by the pump in meters e. Water Power in KW f. Brake Power in KW g. Energy consumption for 15 hours operation in KW-hr h. Line current drawn by the 3-Phase motor drive in amperes i. Pumping cost in Pesos/Day if electricity costs P7.00/KW-hr Figure: Other Data Water Temperature: 20∘C Suction Line 5−20 m 1−90∘ Elbow 1− Check Valve (Fully Open) Pipe Material: Galvanized Iron ND=100 mm Discharge Line L=50 m 12−90∘ Elbow 1− Gate Valve (Fully Open) 1− Check Valve Pipe Material: Galvanized Iron ND =80 mm Pump Efficiency: 75% Motor Efficiency: 82% Volts: 220 V Power Factor: 92%
In a venturemeter used for measuring the flow of oil (S = 0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical U tube containing mercury. If the difference level between the fluids in the U-tube arms is (x +1/S.N ) in cm, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a special fluid of SG=1.2, determine the total head lost.
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other one in the inlet pipe 320 mm below the throat. The difference between the gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses. (b)Working from Bernoulli's equation, determine the difference in level (in millimeters) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil.
Water flows through a pipe at 130 L/s that changes gradually in diameter from 154 mm at point A to 429 mm at point B. B is 4.6 m higher than point A. The respective pressures at A and B are 70 kPa and 48.30 kPa. All minor losses are insignificant. Determine the total head lost.
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc