A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction yard to lift a bridge section weighing 38 kN, as shown in Figure Q2(a). The cable has an effective modulus of elasticity E =140 GPa. (i) If the cable is 14 m long, how much will it stretch when the load is picked up? (ii) If the cable is rated for a maximum load of 70 kN, what is the factor of safety with respect to failure of the cable?

A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction yard to lift a bridge section weighing 38 kN, as shown in Figure Q2(a). The cable has an effective modulus of elasticity E =140 GPa. (i) If the cable is 14 m long, how much will it stretch when the load is picked up? (ii) If the cable is rated for a maximum load of 70 kN, what is the factor of safety with respect to failure of the cable?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.6P

See similar textbooks

Similar questions

A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
A solid circular steel cylinder S is encased in a hollow circular aluminum tube A. The cylinder and tube are compressed between the rigid plates of a testing machine which applies forces P. Calculate the allowable value of the compressive force if the yield stresses of sleel and aluminum are srs = 50 Ksi and ??A= 60 ksi, respectively. Assume that As= 12 in2. AA= 6 in2. L = 20 in., Es= 29,000 tsi and EA=10,600 ksi
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Solve the problem below. For your final answer, use whole number. An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
One side of a petrol drill pipe, as shown in the figure, has been lifted with the use of a crane P force. The outer diameter of the pipe is d0=114 mm and the inner diameter is di=92 mm. The total length of the pipe is L=9 m. The weight of the unit length of the pipe is q=280 N/m. For the inclination angle of the pipe axis θ=300,(a) Draw the cross-sectional diagram of the pipe,(b) Find the cross-sectional effects that pass through B and act on the cross section perpendicular to the pipe axis,(c) Find the principal normal stresses and the maximum shear stress at the B point of the pipe. Note: Maximum area static moment of the pipe section Qmax=(d03-di3)/12 (here Q,, τ=VQ/It).
A safety valve (pressure relieve valve) on top of a pressure vessel containing steam under pressure p = 2 MPa, has a discharge hole of diameter d = 10 mm as shown in the figure below. The valve is designed to release the steam when the pressure reaches the maximum allowable value pmax = 2.23 MPa. If the free height (i.e., uncompressed height) of the spring hfree = 135 mm and its spring stiffness k = 5 kN/m, what should be the dimension h of the valve?
A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter equal to 5.79mm. If the resisting torque supplied by the table is equal to 0.36 N.m, what is the maximum shear stress of the drill bit? If the allowable shear stress in the drill bit is 44.215MPa, what is the maximum resisting toque before the drill binds up?
A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress τmax in the shaft? (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter dmin of the shaft? A solid circular bar of diameter d = 50 mm is twisted in a testing machine until the applied torque reaches the value T = 500 Nm as shown in Fig.4. At this value of torque, a strain gage oriented at 45 ° to the axis of the bar gives a reading ε =339 ×10-6 . What is the shear modulus G of the material?
A weight of 400 N is dropped through a height of 600 mm onto a closed coil compression spring which instantaneously compresses by 200 mm under the impact. The diameter. of spring wire is 25 mn and mean diameter of coil is 200 mm. Find maximum instantaneous stress produced by impact, and number of coil in spring take G=30 kN/mm¹.
Imagine that a long steel wire hangs vertically from a high-altitude balloon.(a) What is the greatest length (feet) it can have without yielding if the steel yields at 44) ksi?(b) If the in wire hangs from a ship at sea, what is the greatest length? (Obtain the weight densities of steel and seawater from Table I-I. Appendix I.)
A column is installed on two bearings and carries a pulley weighing 550 in the vertical direction in the middle of us in the figure. The pulley is connected to the shaft by means of a cog, and the pulley moves the transmission belt in the horizontal direction, the total tension in it is (3500), so if the received power is (15KW) at the speed (150rpm), find the diameter of the shaft required by imposing the permissible shear stress of 140MPa, and in tensile or bending it is equal to 220MPa
A square plastic bar (length LP,side dimension sp=193 mm) is inserted inside a hollow.square cast iron tube (length Le = 400 mm. side sc=200 mm,and thickness tc=3 mm). (A)What is the required initial length L,of the plastic bar so that.ilcn it is compressed by some force the final length of bar and tube are equal to length L and,at the same time, the gap beten plastic bar and cast iron tube is closed? (B) Compare initial and final volumes for the plastic bar. Assume that E = 170 GP E,= 2.1GPa.v = 0.3.and = 0.4.