A steel gear is to be mounted on a solid steel shaft using an interference fit H6/s8. The gear has 17 teeth cut to a module of m-5 mm. The shaft diameter is 52 mm. The gear face width is 50 mm. What is the torque transmission capacity for this mounting? Assume a steel-on-steel friction coefficient of 0.6. The gear does not have protruding hub and it can be treated as a disc the thickness of which is equal to the face width of the gear teeth.Pick the closest answer in N-m. O 1721 O2898 O 7036 O 5396

A steel gear is to be mounted on a solid steel shaft using an interference fit H6/s8. The gear has 17 teeth cut to a module of m-5 mm. The shaft diameter is 52 mm. The gear face width is 50 mm. What is the torque transmission capacity for this mounting? Assume a steel-on-steel friction coefficient of 0.6. The gear does not have protruding hub and it can be treated as a disc the thickness of which is equal to the face width of the gear teeth.Pick the closest answer in N-m. O 1721 O2898 O 7036 O 5396

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut. A.Determine the diametral pitch, B. face width, C. and tooth numbers if the material is cast iron, class 25
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotatingat 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40and 655M13, respectively State the design specification considering the following design factors:1. Functionality2. Stress
A 21-tooth pinion rotating at 1000 rpmrpm meshes with a 33-tooth gear in a spur-gear reducer. Both pinion and gear are manufactured to a quality level of 9. A reliability of 0.9 has been specified and the transmitted tangential load is 2500 lblb. Conditions are such that Cm= 1.7. It is proposed that standard 25∘∘, full-depth teeth be used, with both pinion and gear hobbed from an AISI 4140 nitrided steel. The diametral pitch is 6, and the face width 2.000 inin. Suppose that the life of the pinion will be less than that of the gear, the lubricant bulk temperature does not exceed 250∘F∘F, both driver and driven devices are smooth-running, the gearset is external, gears made by conventional methods. Use the average value for the uncorrected surface-fatigue strength when choosing it from the appropriate table. Assume that the reducer is used for critical service applications. a)What is the dynamic factor (Cv) for the pinion? b)What is the AGMA Surface-Geometry Factor(I) for the pinion/gear…
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion. If the pinion has 20 teeth, use the Lewis formula to determine the face width of thepinion and gear. Then, do one set of calculations and tabulate the answers.
A 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear. Part A Find the appropriate standard diametral pitch for the gearset. Part B Find the minimum required face width of the gears needed to satisfy the safety requirements
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
A Design of Single Reduction Spur Gearbox An input shaft connected to the motor rotates at 1200 rpm, while the output speed must be 570 rpm. The contact force between the gears is transmitted through the pressure angle of 20°. The radial force is 321,90 kN. The material for both gear and pinion is 817M40. 1.1) select the suitable gear and pinion (make use of the Lewis formula). Then, do one set of calculations for single reduction gearbox
A 35 kW motor running at 1200 rpm drives a compressor at 780 rpm. The arrangement is made through a 90° bevel gearing arrangement. The pressure angle of teeth is 14.5°. The allowable static stress for both pinion and gear are 85 MPa. Determine the number of teeth on the gear, face width, addendum, dedendum, outside diameter and slant height, thickness of tooth. Also check your design from the standpoint of wear. Take surface endurance limit as 690 MPa and modulus of elasticity as 89 kN/mm2.
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
A pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Find : $ if there is an interference $length of action and contact ratio $ if centher ditance was increased by 3mm, find backlash produced
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
A pair of straight teeth spur gear is to transmit 20kw when the pinion at 300rpm.the velocity ratio is 1:3.the allowable static stresses for the pinion and the gear material are 12MPa and 100MPa respectively.the service factor is 1.the pinion has 15 teeth and it's face width is 14 times the module.from the standpoint of strength only and taking into consideration the effect of the dynamic loading Determine; (A) module (B) face width (C) pitch circle diameter for pinion (D) pitch circle diameter for gear Tooth form factor;y=0.153_0.912÷no.of teeth Velocity factor;Cv= 3÷3+v