A steel pipe having yield stress σy = 270 MPa is to carry an axial compressive load P = 1200 kN. A factor of safety of 1.8 against yielding is to be used. If the thickness t of the pipe is to be one-eighth of its outer diameter, Calculate: a) the minimum required outer diameter b) the thickness of the pipe

A steel pipe having yield stress σy = 270 MPa is to carry an axial compressive load P = 1200 kN. A factor of safety of 1.8 against yielding is to be used. If the thickness t of the pipe is to be one-eighth of its outer diameter, Calculate: a) the minimum required outer diameter b) the thickness of the pipe

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress is 490 MPa. and the factor of safety is 2.5. Determine the required thickness I to the nearest millimeter.
A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 1% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoop) stress is.....
A cantilever beam, 100 mm wide by 270 mm high and 9 m long, carries a load that varies uniformly from zero at the free end to 1300 N/m at the wall., Determine the magnitude of the stress in a fiber 50 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?
A flange coupling connects two shafts to transmit 40 kW at 900 rpm. The flanges of the coupling are fastened by 6 bolts of the same material. The bolts are equally spaced around the circumference of the bolt circle. The arc on the bolt circle between two adjacent bolts measures approximately 52.36 mm. Find the size of the bolts if the allowable shear stress for the bolt material is 30 MPa.
A cylinder has an ID of 100 mm and an internal pressure of 50 MPa. Find theneeded wall thickness if the factor of safety n is 2.0 and the yield stress is 250MPa. Use the maximum shear stress theory, i.e. maximum shear stress = yieldstrength/2n
The assembly shown below consists of a brass shell (1) fully bonded to a ceramic core (2). The brass shell [E = 115 GPa; α = 18.7 x 10-6 /°C] has an outside diameter of 50 mm and an inside diameter of 35 mm. The ceramic core [E = 290 GPa; α = 3.1 x 10-6 /°C] has a diameter of 35 mm. At a temperature of 15°C, the assembly is unstressed. Determine the largest temperature increase that is acceptable for the assembly if the normal stress in the longitudinal direction of the brass shell must not exceed 80 MPa.
Compare the torsional rigidities of the following sections: (a) a hollow tube 30 mm outside diameter and 1.5 mm thick (b) the same tube split along its length with a 1 mm gap (c) an equal leg angle section having the same perimeter and thickness as (b) (d) a square box section with side length 30 mm and I .5 mm wall thickness (e) a rectangular solid bar, side ratio 2.5 to I. having the same metal cross-sectional area as the hollow tube. Compare also the maximum stresses arising in each case.
1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa.
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 0.1 m depth.
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.