A steel rod, 20 mm diameter and 800 m long, is rigidly attached to an aluminium rod, 40 mm diameter and 1 m long, as shown in Figure below. The combination is subjected to a tensile load of 40 kN. Find the stress in the materials. Aluminium - Steel A 40 kN 40 kN 200 400 800 1000

A steel rod, 20 mm diameter and 800 m long, is rigidly attached to an aluminium rod, 40 mm diameter and 1 m long, as shown in Figure below. The combination is subjected to a tensile load of 40 kN. Find the stress in the materials. Aluminium - Steel A 40 kN 40 kN 200 400 800 1000

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.5.9P: Solve the preceding problem for an aluminum plate with sx= 12,000 psi (tension). sy= -3000 psi...

See similar textbooks

Related questions

Q: Two initially straight bars are joint together and attached to support as shown in Figure 4. Let us…

A: We have to determine a ) If the supports are unyielding , find the normal stress in each bar . ( b )…

Q: Two round solid bars of different materials are connected in series against rigid (b) supports as…

A: Given data:

Q: A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000 N. If the…

Q: The bar shown in Fig. is subjected to a tensile load of 50 kN. Find the diameter of the middle…

Q: A steel rod with a cross-sectional area of 0.20 in is stretched between two fixed points. The…

Q: A cylinder head of a steam engine is held on by 14 bolts. The effective diameter of the cylinder is…

Q: Calculate the extension of the bar (△L).

A: Calculate the extension of the bar (△L)

Q: Step by step

A: This is the very basic question of strength of material portion. Used concept is elongation of a bar…

Q: A rod is composed of three segments, as shown in the figure. Compute the stress induced in each…

A: Given: temperature drop =30oC To determine: Stresses in each material a) if walls are rigid b)…

Q: Ql: A bar ABCD shown in Figure (1) below consists of three sections: AB is of 42 mm diameter and 80…

Q: A cast iron plate in biaxial tension is subjected to a tensile stress σxx = 31 MPa and σyy = 17 MPa…

Q: Find the maximum stress induced in the following cases taking stress concentration into account: 1.…

Q: An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial…

A: Given Data The axial compressive load applied is: P=200 kN The temperature drop is: T=20 K=253.15°C…

Q: The bronze bar 3.43 m long with a cross-sectional area of 564 mm2 is placed between two rigid walls.…

Q: steel:210000 E (MPa) copper:100000 E (MPa) L4 (cm)= 280 L5 (cm)= 255 P1(kN)= 220 P2(kN)= 76 In…

Q: Two initially straight bars are joint together and attached to support as shown in Figure 4. Let us…

Q: A rod is composed of three segments, as shown in the figure. Compute the stress induced in each…

A: Part (a) Write down the given values for the bronze rod. Here Eb signifies bronze young modulus, αb…

Q: Determine the total deformation of the steel rod shown in figure (1) under the given loads. Take the…

Q: A copper bar of 20 mm dia is tightly fitted inside a steel tube of external dia of 30 mm. the length…

A: Given: P=60KN Es= 200KN/mm2 Ec= 160 KN/mm2 di=20mm do = 30mm area of copper(Ac) = π/4*di2 =…

Q: See the figure below. AD is a member with varying diameters. There are three axial loads applied at…

A: Given data: The magnitude of the force acting at the point B is; F1=10 lbs. The magnitude of the…

Q: 12. A composite bar made up of aluminium bar and steel bar, is firmly held between two unyielding…

A: Please find the answer below

Q: A thin cylinder 95 mm internal diameter, 500 mm long with walls 4.5 mm thick is subjected to an…

A: A thin cylinder is a cylinder in which the thickness is the 20th part of the diameter or even less.…

Q: Two initially straight bars are joint together and attached to support as shown in Figure 4. Let us…

Q: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a…

Q: Two initially straight bars are joint together and attached to support as shown in Figure 4. Let us…

Q: The bronze bar 2.7 m long with a cross-sectional area of 415 mm2 is placed between two rigid walls.…

Q: * The rectangular block of material of length L and cross-sectional area A tits snugly between two…

Q: a. An eccentric load of 95 kN acts on a bracket as shown in Figure 6 at its free end. In the…

A: eccentric load, p=95KNeccentricity e=25+202=35cmallowable sheer stress ζ=10000N/cm2

Q: A tensile load of 6 kN at 25 C was applied to a steel rod stretching between two rigid walls as…

A: Given: F= 6 kN T=25°Cα=12.2 μm/(m°C)E=200 GPaσ=150 MPa

Q: The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the…

A: Given Data For Steel E=200 GPaA=1600 mm2α=12×10-60Cσall comp=200 MPa For Aluminum E=73 GPaA=2400…

Q: 1. A steel bar 8 m long, hanging vertically supports a tensile load of 2500 N. Neglecting the weight…

Q: A steel bar of 30 mm * 30 mm square cross section is subjected to an axial compressive load of…

A: As per given A=30×30mm Load=300kn We have to determine contraction of bar

Q: 1.5 Figure 1.9 shows a circular steel rod of length 40 m and diameter 8 mm, which hangs in a mine…

Q: A rod is composed of three segments, as shown in the figure. Compute the stress induced in each…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: The bronze bar 3.42 m long with a cross-sectional area of 627 mm2 is placed between two rigid walls.…

Q: ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is…

Q: Quiz 2: A bronze bar 3 m long with a diameter of 20 mm is placed between two rigid walls as shown in…

A: Given Data Length of the bar, L=3m Diameter of the bar, d=20mm Compressive stress, 35MPa Young…

Q: 20mm diameter bronze bar 3.4m long is place between two rigid walls. at a temperature of -31°C, the…

A: Given Data D=20 mm L=3.4 m T=-31°C ∆= 4.7mm alpha = 19.59x10^-6 m/(m.°C) E= 87GPa.

Q: Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long…

Q: The figure below are cables ( circular section) supporting a 48 kN. Find the axial stress of each.…

Q: 1.5-2 A bar of length 2.0 m is made of a structural steel having the stress-strain diagram shown in…

A: Length of bar L=2 m σy=250 MpaE=200 Gpaelongation when axial load is applied ∂l=6.5 mm

Q: A prismatic bar PQRST is subjected to axial loads as shown in the figure. The segments having…

Q: 2.15 The bar shown below must carry a tensile load of 200 kN. Calculate the diameter of the middle…

A: Dear student, According to the guidelines, I am allowed to answer only one…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure…

A: GIVEN DATA- FOR STEEL AREA=500mm2 , STRESS=200MPa FOR AL AREA=400mm2 , STRESS=115MPa FOR BRONZE…

Q: Problem 1: A steel rod with a cross-sectional area of 0.20 in² is stretched between two fixed…

A: Given data: The cross-section area is The 1st temperature is The tensile load is The 2nd…

Q: A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a…

Q: Q.3. The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid…

Q: A tensile load of 6 kN at 25 C was applied to a steel rod stretching between two rigid walls as…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: A bronze bar 3 m long with a cross sectional area of 320 mm2 is placed L = 3 m between two rigid…

A: For solution refer below images.

Q: The frame in the figure is made of bars that have a square (solid) cross section of 3 cm on each…

A: Given:

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

Deformable

7:45 .l"il
A @ 22 4
A steel rod, 20 mm diameter and 800 m long, is rigidly attached to an aluminium rod, 40 mm
diameter and 1 m long, as shown in Figure below. The combination is subjected to a tensile
load of 40 kN. Find the stress in the materials.
Aluminium
Steel
A
40 kN
40 kN
200 B
400
800
1000

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem for an aluminum plate with sx= 12,000 psi (tension). sy= -3000 psi (compression), dimensions 20 × 30 × 0.5 in.. E = 10.5 × 106 psi, and v = 0.33.
Solve the preceding problem using the fol low-data: W 8 × 21 section, L = 84 in., P = 4.5 kips, a = 22.5°.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Solve the preceding problem for the following strains: x=120106,y=450106,andxy=360106.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A cube of cast iron with sides of length a = 4.0 in. (see figure) is tested in a laboratory under triaxialsire.ss. Gages mounted on the testing machine show that the compressive strains in the material arc a = -225 X l06and,ay = 37.5 X l0_. Determine the following quantities: (a) the norm al stresses i. r,.. and acting on the x, y, and z faces of the cube; (b) the maximum shear stress r in the material; (C) the change ..W in the volume of the cube: (d) the strain energy U stored in the cube; (e) the maximum value of s when the change in volume must be limited to O.O28%; and (f) the required value of when the strain energy must be 38 in.-lb. (Assume £ = 14,000 ksi and v = 0.25.)