A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 10 in a length of 26 diameters. Compute the proper diameter if G = 83 GPa. [Note: Attach your solution] %3D

A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 10 in a length of 26 diameters. Compute the proper diameter if G = 83 GPa. [Note: Attach your solution] %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: 3.10 The stepped steel shaft carries the torque T. Determine the maximum allow- able magnitude of T…

Q: 2. A geothermal power plant has the thermal energy at well head of 1,289 KJ, mass of the liquid of…

Q: surface at 80°C is losing heat to the surrounding air at 25°C by convection with a convection heat…

Q: A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14…

Q: Knowing that at the instant shown the angular velocity of rod AB is 22 rad/s clockwise, determine…

Q: F. What is the compression ratio?

A: Given: T3= 2500 deg F. T4= 886 deg F To find : Compression ratio

Q: Q1:-Answer the following statements with (True) or (False), (choose 5 only) 1-The Bernoulli's…

Q: You have 4 springs, one each 3.5, 6, 8.5, 11 newtons per meter. How close an equivalent stiffness…

Q: 2.Compute the efficiency of the Combustion Chamber and the thermal efficiency of a Gas Turbine Power…

Q: ᴛʜᴇ ᴇᴠᴀᴘᴏʀᴀᴛᴏʀ ᴀɴᴅ ᴄᴏɴᴅᴇɴꜱᴇʀ ᴛᴇᴍᴘᴇʀᴀᴛᴜʀᴇ ᴏꜰ ᴀ 20 ᴛᴏ-ᴛᴏɴ -ᴄᴀᴘᴀᴄɪᴛʏ ꜰʀᴇᴇᴢᴇʀ ᴀʀᴇ -28 degree ᴄ ᴀɴᴅ 23…

A: The T-s diagram of the given system is Given data, Refrigerating capacity of the system, RC = 20 TR…

Q: ) Rate of heat rejection from the turbine

Q: 1. Determine the force in members BC, FC, and EF of the truss and state if these members are in…

A: To find the forces in the given members.

Q: Example 2: The acceleration of a particle moving along a straight line is a= s m/s², where s is in…

Q: a) Specify the percent maximum hysteresis based on full-scale range. b) Referring to increasing…

A: the following is the voltmeter calibration datathe suitable scale for the table given will be re…

Q: Water from a reservoir is pumped over a hill through a pipe 3 ft. in diameter, and a pressure of 35…

A: Given Data : pressure at summite=35 psi pumped quantity = 55cfs pump above resorvoir=300 ft head…

Q: Given the conditions on a converging-diverging wind tunnel. At the reservoir pressure is measured to…

A: Gas passes through the nozzle from a high-pressure zone (known as the chamber) to a low-pressure…

Q: Enthalpy, Ideal Work, Work Lost, Enthalpy Generation. A compressor accepts an ideal gas at T1 = 500…

A: Since we answer up to 3 subparts so we will answer first 3 . Please resubmit the question by…

Q: A Diesel air-standard cycle has a compression ratio of 17.6:1. The pressure and temperature at the…

A: Given dataDiesel air standard cycle has the following propertiesCompression ratio = CR= 17.6 =…

Q: The absolute pressure in a gas tank is 300 kPa. Determine the gauge pressure. Calculate the…

Q: Make a cut in the beam a distance x to the right of point A so that 5.0 ft < x< 10.0 ft. The…

Q: Given the beam cross-section provided below, determine the maximum allowable bending moment that…

Q: 1. Draw and explain about Helical Gears 2. A circular disc mounted on a shaft carries three attached…

Q: e maximum shear stress in thi

A: Given: Diameter (d)= 1.5m Wall thickness (t)= 65mm Internal Pressure= 20 Mpa To find : Maximum…

Q: A pair of bevel gear, 5-pitch, 14.5 °, involute have 3:1 reduction. The pitch diameter of the driver…

A: The teeth of bevel gears are tapered conical pieces that run in the same direction as the pitch cone…

Q: Determine the critical mach number according to linear theory

A: Given Local mach number, MA = 0.435 Streamline mach number, M0 = 0.3 Find Critical mach…

Q: Consider the following statements: A. The weight of a body produces a tendency to rotate. B. The…

Q: 2. An engine working on Otto-cycle receives 1500 k/kg amount of heat. The pressure and temperature…

Q: Determine the moment M which the motor must exert in order to position the uniform slender bar of…

Q: 4. 3) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes the collar A to move…

Q: Oil (y = 48lbf /ft°, p = 2 x 105 lbf x s/ft2 and Pv = 1.9 PSI) is pumped into the system showing a…

A: Calculate the angular velocity of centrifugal pump. Here, the rotations of pump is . Substitute 750…

Q: A cold worked Al-alloy component takes 200 minutes to recrytallize at 250 °Č but takes 14 minutes at…

A: Solution: Given Data: t1=200 minutesT1=250oCt2=14 minutesT2=276oCT3=320oC…

Q: 4. 2) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes the collar A to move…

Q: Fill in the blanks: The ratio of volume at the end of expansion to the volunbelat beginntng of…

Q: Part A In (Figure 1), a: = 8.6 ksi. Determine the principal stresses and the absolute maximum shear…

A: Given Data: Stress, σz=8 Ksi

Q: The acceleration of a particle is defined by the relation a = -kVv, where k is a constant. Knowing…

Q: 2. A piece of ceramic of mass equals to 0.015 kg initially at 15°C receives 45000J in form of heat…

Q: Consider an air-standard Otto cycle that has a compression ratio of 8 and a heat addition of 1330…

Q: A crate of mass 68 kg is pushed along a floor with a force of 30-0 N for a distance of 7.2 m.…

A: Given data : Distance (d)=7.2 m Force (F)=30 N To find : Work done

Q: Part A The door is made from one piece, whose ends move along the horizontal and vertical tracks.…

Q: Find stress Force=2 N Area of cross section=1 m2

A: Given data : The value of force applied F=2 N The value of cross sectional area A=1 m2 Required :…

Q: Find modulus of elasticity Stress=30 Pa Strain=0.5

A: Given data : Stress=σ Strain=ε To find : Modulus of elasticity

Q: Consider the truss shown in the figure below. Calculate the reaction of the roller support at point…

A: Taking moment about point A B*5=10*10+10*(10+10) B*5=100+200 B*5=300 B=60 lbs

Q: Draw the shear and moment diagrams and then answer the questions. Assume w = 7.1 kN/m, a = 305 mm, b…

Q: For a constant tensor, Ajk prove that V(A x, x )= (Ay + Ay )x,.

A: Steps: a) The component of symmetric tensor M(μν) and anti - symmetric tensor M[μν]…

Q: An extension spring made from A313 stainless steel has a mean coil diameter of 10.00 mm and spring…

Q: Draw the shear and moment diagrams for the diving board, which supports the 175-lb man poised to…

Q: rectangular dam has a height and width of 25 m and 15 m, respectively. The depth of water on one…

A: Given:h=25 mw=15 mhw=20 mμ=0.8N=2.31

Q: Consider the two point BVP: -u" + 3u = 1, 0 <x<1, with u(0) = u(1) = 0

A: A two-point boundary value issue is defined when the solution and derivatives are stated at only…

Q: A rotor of a stepper motor is connected to a gear (gear ratio of 1:4). If the rotor rotates at a…

A: Given Speed of driver, N1 = 60 rpm Gear ratio, G = 1:4 Find Speed of driven, N2

Q: A crate of mass 68 kg is pushed along a floor with a force of 30.0 N for a distance of 7.2 m.…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A steel shaft is to transmit 4.5 MW at 3 Hz without
exceeding a shearing stress of 50 MPa or twisting
through more than 10 in a length of 26 diameters.
Compute the proper diameter if G = 83 GPa. [Note:
Attach your solution]
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A thin-walled steel tube having an elliptical cross section with constant thickness t (see figure) is subjected to a torque T = 18 kip-in. Determine the shear stress and the rate of twist in degrees per inch) if G = 12 × 106 psi, t = 0.2 in., a = 3 in., and b = 2 in. Note: See Appendix E, Case 16, for the properties of an ellipse.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A hollow steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 1deg in a length of 26 diameters. Compute the proper diameter if Do =2Di. Show your complete solution.
Please solve clearly step by step otherwise don't attempt.will report. A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the mean torque. The shear stress in the shaft should not exceed 46 MPa and the twist 1.2° per metre length. Determine the diameter required if, (i) The shaft is solid
A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?