A steel surveyor's tape is to be used to measure the length of a line. The tape has a rectangula section of 2 cm by 0.5 cm and a length of 100 cm when T and the tension or pull on the tape is AA N. Determine the true length of the line if the tape shows the reading to be BB cm when used with a pull of CC N at T, The ground on which it is placed is flat. Take: T = T = 57 °C P 87 °C AA = 20 N 2 cm ВВ 3D 463.22 ст

A steel surveyor's tape is to be used to measure the length of a line. The tape has a rectangula section of 2 cm by 0.5 cm and a length of 100 cm when T and the tension or pull on the tape is AA N. Determine the true length of the line if the tape shows the reading to be BB cm when used with a pull of CC N at T, The ground on which it is placed is flat. Take: T = T = 57 °C P 87 °C AA = 20 N 2 cm ВВ 3D 463.22 ст

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

The triangular plate is fixed at its base, and A is given a horizontal displacement of Δs′= 4 mm. Suppose that L=800 mm.
Determine the range of values of v for which both wires remain taut. Where x1 is the last digit of your student’s ID (if it is zero then add 4 to it), and x2 is last tow numbers of your ID separated by a decimal point (etc. if last two numbers are 66 then x2 is 6.6 m), x3 in degrees taking as 50o
The force P is applied to the bar, which is made from an elastic perfectly plastic material. Construct a graph to show how the force in each section AB and BC (vertical axis) varies as P (horizontal axis) is increased. The bar has cross-sectional areas of 1 in2 in region AB and 4 in2 in region BC. Take sY = 30 ksi.
Solve Prob. 7.29 if =0.
The cable AB supports a uniformly distributed load of 12 lb/ft. Determine the angles A and B, and the cable tension at A.
The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.
The polyvinyl chloride bar is subjected to an axial force of 900 lb. If it has the original dimensions shown, determine the change in the angle u after the load is applied. Epvc = 800(103) psi, npvc = 0.20.
Determine the vertical displacement of plate A due to shear deformations in the rubber. The cross-sectional dimensions of each shoe are 35mm X 25mm. G = 0.3 Mpa,
A P collar slides along the OA pipe. A PC elastic cord is attached to it and it is held at point C of the BC pole. Determine the OP distance when PC and OA are perpendicular.
Cable S is tethered to the roadway at angle θ = 57.0 ∘ . Find the change in the length of cable S when the tractor trailer causes the roadway to drop 0.4 cm . Assume that cable S remains tethered to the roadway at angle 57.0 ∘ .
Determine the normal tension of the cylinder piston rod (diameter 32mm). The clamping force of the pliers is 6000N. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Use the units [N, mm], ie the answer comes in MPa !!! Please enter a numeric value only !!
Perform the operation g(t)=2t+5f(t)= 2t+5find: (g+f)(t)