A steel tape having a cross-sectional area of 0.06 sq. cm. and a modulus of elasticity of 2.0x10^6 kg/sq. cm., weighs 0.03 kg/m. Its length is 30.00 m when standardized at a pull of 5 kg and supported throughout its length. Determine the normal tension at which the effect of sag will be eliminated by the elongation of the tape due to increased tension

A steel tape having a cross-sectional area of 0.06 sq. cm. and a modulus of elasticity of 2.0x10^6 kg/sq. cm., weighs 0.03 kg/m. Its length is 30.00 m when standardized at a pull of 5 kg and supported throughout its length. Determine the normal tension at which the effect of sag will be eliminated by the elongation of the tape due to increased tension

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 30-m steel tape supported at its ends weighs 0.03 kg/m and is of standard length under a pull of 6.5 kg. If the elastic modulus of steel is 2.0 x 10⁶ kg/cm² and its weight density is 7.9 x 10^-3 kg/cm³, determine the tension at which the effect of sag will be eliminated by the elongation of the tape due to increased tension.
A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. What normal tension ( N ) is required in order that the effect of sag will be eliminated when the tape is supported at end points only? The standard pull is 10kg. Tape area is 8 mm2. E = 200 GPa. need answers and solutions asap, thank you!
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
A 30-m steel tape weighing 1.45 kg is of standard length under apull of 5 kg, supported for full length. A line 938.55 m long wasmeasured using the tape with a steady pull of 10 kg.If E = 2.0x106 kg/cm2 and unit weight of steel is 7.9x10-3 kg/cm3,determine:a) cross-sectional area of the tape
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point E. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point E. Express your answer in kilopounds to three significant figures. c) Determine the moment at point E. Express your answer in kilopound-feet to three significant figures.
Consider the simply supported beam shown in (Figure 1). Suppose that P = 18 kN , w = 7 kN/m . Point D is located just to the left of the 18-kN concentrated load. Follow the sign convention. Part A Part complete Determine the internal normal force at point C. Express your answer to three significant figures and include the appropriate units Part B Determine the internal shear force at point C. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at point C. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at point D. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at point D. Express your answer to three significant figures and include the appropriate units. Part F Determine the internal moment at…
A wooden I- beam is made up with a narrow lower flange because of space limitations, as shown in the figure. The lower flange is fastened to the web with nails spaced longitudinally 6 in apart, and the vertical boards in the lower flange are glued in place. Determine the stress in the glued joints and the force carried by each nail in the nailed joint if the beam is subjected to a vertical shear of 400 lb. The total moment of inertia with the contribution of each part of the beam is shown below. The neutral axis and the total moment of inertia are given–you don’t need to calculate them. The neutral axis (centroidal axis for the overall section) is at a distance 8.58 in from the bottom of the beam, and the total moment of inertia is 2635.86 in4 .
length=7m height=250mm UDL on the beam=38.5KN/M d=812mm Mass of the beam=65.9kg/m a. Consider design loads( udl+self weight) b. Calculate and draw the Bending Moment Diagram (BDM).What is the value of the maximum bending moment? c. Calculate and draw the Shear Force Diagram (SFD).What is the value of the maximum shear force? d. Using the table, calculate the maximumdeflection of the beam.
The uniform beam shown in Figure 2 weighs 500N and supports a 700N load. Find the tension inthe tie rope and the force of the hinge on the beam.
Consider the beam shown in (Figure 1). Suppose that w1 = 520 N/m , w2 = 260 N/m . Follow the sign convention. PartA) Determine the internal normal force at point C.Express your answer to three significant figures and include the appropriate units. PartB) Determine the internal shear force at point C.Express your answer to three significant figures and include the appropriate units. PartC) Determine the internal moment at point C.Express your answer to three significant figures and include the appropriate units.
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point D. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point D. Express your answer in kilopounds to three significant figures. c) Determine the moment at point D. Express your answer in kilopound-feet to three significant figures.