A straight gear with module m = 5 mm and face width bw = 40 mm has center distance cd = 0.1875m. The pinion has 25 teeth, the speed is 1000 rpm, and pressure angle ᶲ = 200. Find the Hertzian contact stress at the pitch point when the gear transmits 10 kW. Neglect friction forces. The gear steel has modulus of elasticity E = 207 GPa and a Poisson’s ratio of 0.30.

A straight gear with module m = 5 mm and face width bw = 40 mm has center distance cd = 0.1875m. The pinion has 25 teeth, the speed is 1000 rpm, and pressure angle ᶲ = 200. Find the Hertzian contact stress at the pitch point when the gear transmits 10 kW. Neglect friction forces. The gear steel has modulus of elasticity E = 207 GPa and a Poisson’s ratio of 0.30.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
. Four gears are attached to a circular shaft andtransmit the torques shown in the figure. Theallowable shear stress in the shaft is 10,000 psi.(a) What is the required diameter d of the shaft ifit has a solid cross section?(b) What is the required outside diameter d if theshaft is hollow with an inside diameter of 1.0 in.?
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.
There are two pairs of closed soft tooth surface spur gears A and B,Parameters of A: modulus m = 2mm, number of teeth Z1 = 40, Z2 = 90 , width of teeth b = 60mm.Parameters of B : modulus m = 4mm, number of teeth Z1 = 20, Z2 = 45 , width of teeth b = 60mm.The accuracy of the two pairs of gears is grade8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason.
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G = 6,500 ksi] tubes, which have an outside diameter of 2.40 in. and a wall thickness of 0.1375 in. Segments (3) and (4) are solid 1.00-in.-diameter steel [G = 11,500 ksi] shafts. The shaft lengths are L1 = 58 in., L2 = 16 in., L3 = 16 in., and L4 = 28 in. The torques applied to the shafts have magnitudes of TB = 970 lb·ft, TD = 430 lb·ft, and TE = 170 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A.
Example 3 (a) A steel transmission shaft is 510 mm long and 50 mm external diameter. For part of its length it is bored to a diameter of 25 mm and for the rest to 38 mm diameter. Find the maximum power that may be transmitted at a speed of 210 rev/min if the shear stress is not to exceed 70 MN/m’. (b) If the angle of twist in the length of 25 mm bore is equal to that in the length of 38 mm bore, find the length of the two bored parts.
Gear B, shown in Figure Q4, supplies 15 kW of power, while gears A , C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of ?????? = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter ? of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm.
The upper half of a compound Epicyclic gearset is shown in Figure, with input shaft I rotating at a constant speed of 700 rpm in a clockwise direction and generating 12 kW input power. The Annulus wheel A2 is coupled to an auxiliary gear N on shaft X and forms a compound wheel with gear O. The Annulus A1 rotates in a counter-clockwise direction at a speed of 5,300 rpm. Calculate the following using this condition: Number of gear teeth:P1 = 30 , A1 = 120P2 = 50 , A2 = 140N = 60 , O = 120 a) The output shaft O (NO), shaft X (NX), and gear ratio speed and direction (n). b) Calculate the speed and direction of output shaft O (NO), shaft X (NX), and gear ratio if Annulus wheel A1 is locked (n). c) The braking torque (Tb) that must be applied to Annulus wheel A1 to keep it stationary (magnitude and direction), assuming gear transmission efficiency of 90%.