A shaft with splines of a diameter of 50 mm, as shown in the figure below, transmits a torque of 1600 N.m to the hub of a gear. If D 50 mm, d = 45 mm, w= 12.5 mm and the length of spline (the width of the hub) is 40 mm: 1. Compute the force, shear stress, and bearing stress on each splines caused by this load. 2. Consider the shift is made from a material has bearing stress and shearing stress of 80 N/mm2 and 60 Mpa respectively, can the splines support the applied load? If not, suggest a solution.

A shaft with splines of a diameter of 50 mm, as shown in the figure below, transmits a torque of 1600 N.m to the hub of a gear. If D 50 mm, d = 45 mm, w= 12.5 mm and the length of spline (the width of the hub) is 40 mm: 1. Compute the force, shear stress, and bearing stress on each splines caused by this load. 2. Consider the shift is made from a material has bearing stress and shearing stress of 80 N/mm2 and 60 Mpa respectively, can the splines support the applied load? If not, suggest a solution.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A keyed sprocket delivers a torque of 778.8 N - m thru the shaft of 54 mm OD. The key thickness is 1.5875 cm and the width is 1.11 cm. Compute the length of the same key. The permissible stress value of 60 MPa for shear and 90 MPa for tension. A. 39.12 cm B. 4.82 cm C. 52.22 cm D. 4.32 cm
In drilling a deep oil well the drill shaft, consisting of sections of “drill rod”, is powered from the top, while the load or counter torque is taken off at the bottom. The drill hole is 3 1/2 miles deep. Assuming a solid drill rod of circular cross section and 1 in. diameter, designed to a working shear stress of 5,000 psi, turning at 700 rpm, calculate (a) The wind-up, i.e. the twist angle between the top and bottom. (b) The horsepower of the driving motor. (c) State all assumptions, and comment on the results. What other considerations may have to be taken into account in using this drill? NOTE: The shear modulus of steel may be taken as 12 x 106 psi. Also 1 mile = 5,280 ft.
Shaft length, L and a different allowable maximum shear stress, τmax and subject to a different Torque, T. For steel use a shear modulus, G=81,000 MPa. A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate: a) The minimum shaft diameter required. b) The angle of twist over the length of the shaft. c) The Power output if your shaft is rotating at 2000 rpm. L= 1.6m, τmax=100MPa , T=1.3kN-m
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
Solid Mechanics A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured. Torsion of spindle of 1200 N.m it is required to carry the moment. Anti-slip protection for shaft material stress 40 MPa, the largest permitted unit torsion angle in the bar 0.750 / m and the shear modulus of the steel is G = 78 GPa. a) Find the required diameter d0 for a solid circular shaft. b) Required for a ring-section shaft whose thickness is one tenth of the outer diameter Find the outer diameter d2. c) Diameter ratios (d2 / d0 for ring and solid section shafts. Find the weight ratios with the ratio).
Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is likely to exceed the mean by 30% for a maximum permissible shear stress of 55. Calculate also the angle of twist for a length of 2m.
Example 3 (a) A steel transmission shaft is 510 mm long and 50 mm external diameter. For part of its length it is bored to a diameter of 25 mm and for the rest to 38 mm diameter. Find the maximum power that may be transmitted at a speed of 210 rev/min if the shear stress is not to exceed 70 MN/m’. (b) If the angle of twist in the length of 25 mm bore is equal to that in the length of 38 mm bore, find the length of the two bored parts.
Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a torque of 1200 Nm. Since the shear strength for the shaft material is 40 MPa, the maximum allowable unit torsion angle of the bar is 0.75 ^ 0 / m and the shear modulus of steel is G = 78 GPa;a) Find the required diameter d0 for a solid circle shaft.b) Find the required outside diameter d2 for a ring-section shaft whose thickness is one tenth of the outer diameter.c) Find the diameter ratio (d2 / d0 ratio) and weight ratio for ring cross section and solid section shafts
A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at the ends. What is the diameter of a solid steel shaft that resists the same torques at the same maximum shear stress.
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
Solve the problem below. For your final answer, use whole number. An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner diameter. It is rigidly attached to the wall at A. Externaly applied torques are TB of 1338 lb-ft, Tc of 1117 lb-ft, and TD of 884 lb-ft. Firstly obtain the internal torque generated, then calculate and input the maximum shear stress in section BC of the shaft: (f v max) = ___________ lb/in.2. Pay attention to unit conversion and calculate your answer to 1 decimal place.