A tank and a deflector are placed on a frictionless trolley. The tank issues water jet (mass density of water = 1000 kg/m³), which strikes the deflector and turns by 45°. If the velocity of jet leaving the deflector is 4 m/s and discharge is 0.1 m³/s, the force recorded by the spring will be Spring 0000000 Tank Jet of water 45° 2 Deflector ITIT Trolley

A tank and a deflector are placed on a frictionless trolley. The tank issues water jet (mass density of water = 1000 kg/m³), which strikes the deflector and turns by 45°. If the velocity of jet leaving the deflector is 4 m/s and discharge is 0.1 m³/s, the force recorded by the spring will be Spring 0000000 Tank Jet of water 45° 2 Deflector ITIT Trolley

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. An open cylindrical tank 2 m in diameter and 4 m high contains water to a depth of 3 m. It is rotated about its own vertical axis with a constant angular speed. a. If w = 8 rad/s, how much water is spilled out and to what depth will the water stand when brought to rest?b.What angular speed w (in rpm) will just zero the depth of water at the center or the tank?c.If w = 100 rpm, how much area at the bottom of the tank is uncovered?
The wooden block (mass m = 0.5358 kg) is released from rest at A by a compressed spring (compressed length 0.6 m, undeformed length 1 m, spring constant k = 150 N/m). The block is allowed to slide through the rough horizontal surface (A to B), then along the smooth circular ramp (B to C, central angle θ = 47.2°, until the block is released after point C. Calculate the speed of the block at points B and C. Also, what is the magnitude of the normal force exerted to the block just before the block leaves the ramp? Neglect the geometry of the block.NOTE: Use Work-Energy Method to solve for the speeds; use Force-Mass-Acceleration (FMA) Method to compute for the normal force.
. A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The sucLon pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diameter and 150 m long. if the velocity in the pipe is 3 m/s, the fricLon factor of the pipe 0.008, and the pump and motor efficiencies 85 % and 92 %, respecLvely. See Figure Q6.1. Calculate:(a) Gauge pressure at the pump's inlet (at C) (10)(b) Gauge Pressure at the pump's outlet (at D) (10)(c) input power to motor (5)
The crank and connecting rod of a theoretical steam engine are 0.4 m and 1.6 m long, respectively. The crank makes 180 rpm in clockwise direction. When it has turned 45° from the inner dead center position, determine the: a) Velocity of piston, b) Angular velocity of connecting rod
Water flows at 1.52 m/sec from a reservoir into a 900 mm diameter steel pipe that is 2286 m long and has a thickness of 25 mm. find the water hammer pressure developed by closure of a valve at the end of the line if the closure time is 8 sec. the velocity (celerity) of a pressure wave C=1440m/s, modulus of elasticity of water = 200 MPa and that of steel is 200,000 Mpa. Answer: 868.2 kPa
Determine the angular acceleration of the 23-kg diving board the instant the man jumps off. Assume that the board is uniform and rigid, and that at the instant he jumps off the spring is compressed a maximum amount of 210 mm , ω=0, and the board is horizontal. Take k = 6.0 kN/m and Determine the vertical component of reaction at the pin AA the instant the man jumps off.
The 14.6 lb lever OA with 9.6 in radius of gyration about O is initially at rest in the vertical position (?= 90°) where the attached spring of stiffness k = 4.3 lb/in is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity ? = 5.9 rad/sec as the lever reaches the horizontal position ? = 0.
5. End A of the 6kg uniform rod AB rests on the inclined surface, while end B is attached to collar of negligible mass which can slide along the vertical rod shown. Knowing that the rod is released from rest when ? = 35° and neglecting the effect of friction, determine immediately after release (e) The angular acceleration of the rod, (f) The reaction at B.
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Fluid mechanics, i need solutions in 10 minutes please. Q/Q2 The 4 -m- diameter circular gate of Fig. E2.6a is located in the inclined wall of a large reser voir containing water (y = 9.80 kN / m³). The gate is mounted on a shaft along its horizon tal diameter. For a water depth of 10 m above the shaft determine: (a) the magnitude and lo cation of the resultant force exerted on the gate by the water, and (b) the moment that would have to be applied to the shaft to open the gate.
A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other end. The tank has a diameter of 1.2m and a height of 3.6m. It is then rotated about its vertical axis with an angular speed w. a. Determine w in rpm so that one third of the volume of water inside the cylinder is spilled. b. Determine the largest pressure developed in the tank.
An inverted differential manometer is connected to two pipes A and B whichconvey water. The fluid in manometer is oil of specific gravity of 0.8. For themanometer readings r = 30 cm, s = 20 cm and t = 30 cm, find the pressuredifference between A and B.