Solve the following problems. Show the complete solution neatly, orderly, and label the answer properly. Each problem is worth 30 points. Problem 1) A simply supported beam is loaded as shown in Figure 1-A. Use E = 40 MPa and 1= 5 x 106 mm². a) Determine the slope at point B. b) Determine the deflection at point B c) Determine the deflection at midspan of the beam. 80 KN 2 m RA 10 kN/m Figure 1 - A 8m C Rc

Solve the following problems. Show the complete solution neatly, orderly, and label the answer properly. Each problem is worth 30 points. Problem 1) A simply supported beam is loaded as shown in Figure 1-A. Use E = 40 MPa and 1= 5 x 106 mm². a) Determine the slope at point B. b) Determine the deflection at point B c) Determine the deflection at midspan of the beam. 80 KN 2 m RA 10 kN/m Figure 1 - A 8m C Rc

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following using slope deflection method: 1. Slope at B, in radians
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and CAssume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15If there is a settlement of S at the support C, solve the following using slope deflection method:
Question 1 For the beam and loading shown, using the conjugate method, determine the slope at C in degree measure. Use three decimal places. Express your final answer in absolute value. Assume E = 15,000 MPa and I = 2 x108 mm4.
For the beam loaded as shown in the figure 3, determine the slope at B in degrees using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places. a = 5.5 m, b = 3.3 m, c = 20.3 kN/m, d = 27 kN.
SHOW COMPLETE SOLUTION Two blocks A and B of weights WA and WB respectively rest on a rough inclined plane and are connected by a short piece of string as shown in the attached figure. If the coefficients of friction between the blocks and the plane are respectively nA = 0.2 and nB = 0.3, find (a) the angle of inclination of the plane for which sliding will impend, and (b) tension in the string.Take WA = WB = 20 N.
PLEASE REFER TO THE GIVEN VALUES BELOW. For the beam loaded as shown in the figure, determine the following unknowns using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Round-off to 3 decimal places. a = 8.5 m, b = 3.3 m, c = 9.5 kN/m, d = 27 kN-m. - Slope of the elastic curve at B in degrees. Indicate negative sign as necessary. - Deflection at D in mm. Indicate negative sign if downward. - Deflection at midspan in mm. Indicate negative sign if downward.
In the rectangular figure shown, specific gravity of concrete is 2.4 and the coefficient of friction between the dam and foundation is 0.4. Use 1.5 as the FOS against sliding. a. Find the value of overturning moment. b. determine the b of the concrete dam needed to prevent the dam from sliding. c. Is the dam also safe from overturning?
Given a cantilever beam of length L=2.1meters. The left support “A” is free while the right end “B” is fixed. With constant EI=19000 KN-m2 A downward concentrated load of 70KN is applied at “A”. Using Double Integration Method (DIM) with origin taken at point A where 0 ≤ x ≤ L, calculate the deflection at midspan? Express your answer in "mm" in 2 decimal places. Include (-) negative sign if deflection is downward.
Determine the following unknowns on the beam shown below using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Show complete and organized solution. a.Deflection at point B in mm, b. Deflection at point E in mm. C. Slope of the elastic curve at point D in degrees. Given: a- 5m b-11kN/m c-3kN d-7kN/m
A beam is shown in the figure below, and the flexural stiffness of the beam section is constant EI: Use the conjugate beam method (Conjugate Beam Method) to obtain the slope (Slope) after the deformation of point A and the vertical displacement (Deflection) of point C *The correct answer is 24 kN-m2/EI clockwise and 58.7 kN-m3 /EI down, but I need to calculate steps, thanks
Calculate the value of the deflection at point B due to uniformly distributed load w in the form answer in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. QUESTIONS: a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. GIVEN: a. 3.1 b. 18.0 c. 20