A crane is used to lower weights into the sea for an underwater construction project. Determinethe tension in the rope of the crane due to the rectangular 0.4-m x 0.4-m x 3-m concrete blockwhen it is1. suspended in air2. completely immersed in waterIKRopeConcreteblockWT, airFT. waterWFBAirWaterFigure 1: Concrete block in air (top) and immersed in sea water (bottom)What is the percentage decrease in the tension of the rope from when the block is in airto when it is completely immersed in the water?Assume Pconcrete = 2300kg/m³ and Pseawater = 1025kg/m³. g = 9.81m/s².

Answered: Image /qna-images/answer/533239ab-40f1-4a4a-9f77-aa2e200bb15e.jpg

> A crane is used to lower weights into the sea for an underwater construction project. Determine the tension in the rope of the crane due to the rectangular 0.4-m x 0.4-m x 3-m concrete block when it is 1. suspended in air 2. completely immersed in water Z Rope Concrete block AFT. Air Water Figure 1: Concrete block in air (top) and immersed in sea water (bottom) What is the percentage decrease in the tension of the rope from when the block is in air to when it is completely immersed in the water? Assume Pooncrete = 2300kg/m³ and Pseawater = 1025kg/m³. g= 9.81m/s².

> A crane is used to lower weights into the sea for an underwater construction project. Determine the tension in the rope of the crane due to the rectangular 0.4-m x 0.4-m x 3-m concrete block when it is 1. suspended in air 2. completely immersed in water Z Rope Concrete block AFT. Air Water Figure 1: Concrete block in air (top) and immersed in sea water (bottom) What is the percentage decrease in the tension of the rope from when the block is in air to when it is completely immersed in the water? Assume Pooncrete = 2300kg/m³ and Pseawater = 1025kg/m³. g= 9.81m/s².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the load that will compress the combined bar a total of 0.8mm in the lenght of 2m. If the bar is 2m long and surrounded by a cast iron 5mm thick and a bar radius drived from a bar design that can hold 3 liters of liquid with the minimum amount of materials to be used for construction. For steel, E=200 Gpa, and for cast iron, E= 100 Gpa. Prove that the parameters are minimum value.
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG EXPLANATION. ANSWER IN 2 DECIMAL PLACES.) 6.10 The two bars, pinned together at B, are supported by a frictionless surface at A and a built-in support at C. Determine the internal force systems acting on sections 1 and 2.
Engineering MechanicsDETERMINE FORCE (N) OF MEMBER EG in the truss shown.F1 = 222 NF2 = 513 NF3 = 456 Nα = 43 degreex = 13 m. Note: for compression, include a negative sign ( - ) and for tension, type your answer as is. Input answer in two (2) decimal places.
6. The steel gate 2.61m square of thickness 36.1mm is to be lifted by a frictionless pulley. The coefficient of friction between the dam and plate is 0.216 ,calculate the minimum force required to lift the gate if it is fully submerged to a depth of 1.61m. Use specific gravity of steel 8.0 PLEASE ANSWER THIS ASAP!!!
a wooden rog weighing 3lb is hinged at one end. The rod is 17ft long and uniform in cross section and the support is 7ft below the free surface of a freshwater pond. the cross section is 1.4in^2 in area. a what is buoyant force of water acting on the rod, in lb? b. how much length is submerged in water in ft? c. at what angle will it come to rest when allowed to drop from a vertical position?
A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block. Note: The answer should be 13.76 kN or near.
Engineering Mechanics (Like/Thumbs-up will be given. Write the solutions&FBD legibly. Include negative sign if in Compression, ex. -1,500 or if in Tension, ex. 1,500. Round to the nearest whole number.) I. (Multiple Choice) From the given A-Frame shown above, which statements are true: a. The horizontal reaction at C is equal to 0 b. The vertical reaction at A is upward c. The horizontal reaction at pins B and D are equal in magnitude d. Member BD is a two-force member e. None of the above II. (Compute for the external reactions for all members of the frame shown): > Vertical Reaction at A > Horizontal Reaction at A > Vertical Reaction at E > Vertical Reaction at D > Vertical Reaction at B > Vertical Reaction at C > Horizontal Reaction at C > Horizontal Reaction at B > Horizontal Reaction at D
plz plzzzzzz help me nowwww What is the hydrostatic force (kN) that acts on the Gate A-B? Given that the specific gravity of liquid S=8.9.
Determine support reaction. P=800 lb , a=5 ft b=9 ft
Find the tensions in the ropes that hold a 100N box. The ropes are considered weightless and are at respective angles of 37° • and 60° with the horizontal,
Question:- A 7.5 meters long simply supported structural steel beam carries two concentrated loads P at every third points. Use A 572 Grade 65 steel with Fy=448.18 MPa. The beam is W310x23.8 section having the given properties. A=3040mm² d= 305mm tw= 5.6mm bf=101mm tf= 6.7 mm Ix= 43x10⁶ mm⁴ Iy=1.2x10⁶mm⁴ a) Calculate the allowable bending stress of the compression flange of beam 7.5 fully supported against lateral movement. b) Based from the previous question, calculate the value of concentrated load P that the beam could support safety.
Calculate the vertical reaction at support A. Enter your answer in kN to two decimal places.