A tank of oxygen has a hole of area 0.5 cm² in its wall. The temperature of the oxygen in the tank is -35°C. Calculate the rate (kg/s) at which oxygen leaks to the atmosphere for tank pressures of 135 kPa and 375 kPa. Assume frictionless flow. 135= i m375= ! kg/s kg/s

A tank of oxygen has a hole of area 0.5 cm² in its wall. The temperature of the oxygen in the tank is -35°C. Calculate the rate (kg/s) at which oxygen leaks to the atmosphere for tank pressures of 135 kPa and 375 kPa. Assume frictionless flow. 135= i m375= ! kg/s kg/s

Name: Looking for a neat solution using a paper sheet. A tank of oxygen has
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Looking for a neat solution using a paper sheet. A tank of oxygen has a hole of area 0.5 cm² in its wall. The temperature of the oxygen in the tank is -35°C. Calculate the rate (kg/s) atwhich oxygen leaks to the atmosphere for tank pressures of 135 k

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
In a pipeline with converging diameter, will the gradient of the total energy line be steeper or milder than the gradient of the piezometric head line? Why?
0il with p = 876 kg/m³ and u = 0.24 kg/m-s is flow- ing through a 1.5-cm-diameter pipe that discharges into the atmosphere at 88 kPa. The absolute pressure 15 m before the exit is measured to be 135 kPa. Determine the flow rate of oil through the pipe if the pipe is (a) horizontal, (b). inclined 8° upward from the horizontal, and (c) inclined 8° downward from the horizontal.
The impeller of a centrifugal blower has a radius of 18 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disregarding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volumetric flow rate of air when the rotational speed of the shaft is 900 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
Turbines, compressors, boilers, condensers, and heat exchangers operate for long periods of time under the same conditions, and they are classified as __________ flow devices.
A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level is 3 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) while the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine the initial discharge rate of water from the tank
An air compressor takes air at 99 kpa and compress it isentropically at 700 kpag. If volumeflow at discharge is 3 m3/sec, determine the capacity of air in ft 3 /min.
Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an outlet diameter of 20 cm is bolted to the pipe in order to slow down water, as shown in Disregarding frictional effects, determine the force exerted on the bolts due to the water flow.
Orange juice is flowing through a horizontal U-type reducing bend at a rate of 36kg/s. The cross-sectional area, gage pressure, and velocity are 168cm^2, 57.5 kPa, and 2.10 m/s at the inlet, and 80cm^2, 50kPa, and 4.37 m/s at the outlet. Calculate the force applied to the reducing bend by the orange juice in the horizontal direction
Nitrogen at a pressure of 200 kPa and a temperature of 25°C, flow at a velocity of 20 m/s through a pipe with a diameter of 35 mm Working substance:______system:______ Sketch :
Air enters a fan through a duct velocity of 6.3 m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If, the density of the air is 1.2kg/m3and the fan delivers 9.45m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling. Show schematic diagram and provide solutions.
Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1) and 1.8 in at the throat (location 2). The gage pressure is measured to be 12.2 psia at the entrance and 11.8 psia at the throat. Neglecting frictional effects, show that the volume flow rate can be expressed as and determine the flow rate of air. Take the air density to be 0.075 lbm/ft3.