A temp sensor is being calibrated. The temperature is taken from 0 to 100 and back to 0. The following readings were obtained. Plot a graph of the readings to determine if there is hysteresis and if so what is the hysteresis as a percentage of full scale deflection True Temp C 0 20 40 60 80 100 80 60 40 20 0 Sensor Reading 1 19 37 56 78 106 84 64 44 22 1

A temp sensor is being calibrated. The temperature is taken from 0 to 100 and back to 0. The following readings were obtained. Plot a graph of the readings to determine if there is hysteresis and if so what is the hysteresis as a percentage of full scale deflection True Temp C 0 20 40 60 80 100 80 60 40 20 0 Sensor Reading 1 19 37 56 78 106 84 64 44 22 1

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

Given the model for position control system, find the value for K1 and K2 so that the peak time is equal to 0.5s and the %OS is equal to 3%.
16 - What is the name of the series of operations performed to determine the relationship between the value displayed by a measuring instrument and the measured quantity under certain conditions?A) CalibrationB) SensitivityC) ResolutionD) accuracyE) Robustness
Subject Linear Control I need only answer for MCQ please
With AVR ATmega16 microcontroller, a circuit has servomotor (PC0), a potentiometer and two LEDs. Write a program as: when turn the potentiometer’s knob to the right the servomotor will rotate clockwise and the first LED (PB0) will be on. when turn the potentiometer’s knob to the left the servomotor will rotate counterclockwise and the second LED (PB1) will be on.
14.a. An encoder is a device that is used toA. excite the motor's interpoles.B. feed pack position information.C. reduce brush sparking.D. commutate the field windings.14.b. The letters CEMF are used to describeA. centrifugal forces within a motor.B. the portion of the supplied current that is converted to heat.C. countervoltages and currents created within a motor.D. critical winding currents that should not be exceeded.
Subject Linear Control I need MCQ please
The single phase full wave AC voltage controller operates on a single phase supply voltage of maximum voltage as 230 V, at 50 Hz. If the triac is triggered at a delay angle of 45°, during each half cycle of input supply. Find the rms output voltage and input power factor.
1.a. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.Where does this voltage go to?A. The interpolator cardB. The CPU in the main controllerC. The driverD. The axis logic card1.b. A type of feedback device that uses a rotor and senses the position of the motor by means of sine andcosine waveforms is called a/anA. tachometer.B. encoder.C. resolver.D. alternator.
Q8)This Multiple choice questions from electronics lab course &just write for me final answer ,It easy for you.
In a commercial resolver to digital converter the digital angle Φ is determined to be 20 degrees. The output of the summing amplifier is resolver signal A sin (2πft), where frequency f is 60 hz, A = 0.7 volts and the input voltage V to the resolver is 10 volts. What is the rotor angle in the resolver in degrees at time t = .07 seconds? (Type in a one-decimal number)
Good day! Please help me determine the conduction angle in my simulation as well as the delay angle. Please teach me also how to determine it. Thank you! need asap.
Create the MikroC Code for this schematic. It is for controlling and monitoring multiple DC Motors using PIC16F877A. The temperature sensor will utilize the Analog-to-Digital Converter module of a PIC microcontroller, particularly the PIC16F877A. The temperature reading is then displayed continuously on a Liquid Crystal Display (LCD). The temperature sensor and the LCD are connected to the master microcontroller; on the other hand, the other output components are connected to the slave. The two microcontrollers will communicate using the Universal Asynchronous Receiver-Transmitter (UART) module. For the output part of the system, the robot will do its firefighting task if the sensor reaches a reading of 68 degrees Celsisus. Furthermore, the robot also utilizes RGB LED and a buzzer as an output indicator of the system. For the wheels, the researchers represented it using DC motors connected to relays in order for them to be easily turned on and off. In the same way, the water pump of…