The following data relate to a single-cylinder reciprocation engine: A) The following data relate to a single-cylinder reciprocationengine:Mass of reciprocating parts = 50 kgMass of revolving parts= 40 kg at a crank radiusSpeed= 160 rpmStroke= 450 mmIf 60% of the reciprocating parts and all the revolving parts are tobe balanced,Determine:i. The balance mass required at a radius of 420 mmii. The unbalanced force when the crank has turned 45° from thetop – dead center

Given: Mass of reciprocating mass M=50kg Mass of revolving parts m=40kg speed…

A) The following data relate to a single-cylinder reciprocation engine: Mass of reciprocating parts = 50 kg = 40 kg at a crank radius = 160 rpm Mass of revolving parts Speed Stroke = 450 mm If 60% of the reciprocating parts and all the revolving parts are to be balanced, Determine: i. The balance mass required at a radius of 420 mm ii. The unbalanced force when the crank has turned 45° from the top - dead center

A) The following data relate to a single-cylinder reciprocation engine: Mass of reciprocating parts = 50 kg = 40 kg at a crank radius = 160 rpm Mass of revolving parts Speed Stroke = 450 mm If 60% of the reciprocating parts and all the revolving parts are to be balanced, Determine: i. The balance mass required at a radius of 420 mm ii. The unbalanced force when the crank has turned 45° from the top - dead center

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An engine has a turning moment diagram with the areas above and below the mean torque line of -50 mm2, +120 mm2, -100 mm2, +150 mm2,-80 mm2, +70 mm2 and -110 mm2 with the turning moment diagram scales being for the torque 1mm = 100 Nm and for the crank angle 1mm = 2 °. What is the smallest mass a flywheel of radius of gyration 250mm can have, when running at 600 rpm, if the total fluctuation of speed is not to exceed 2% of the means
In a six cylinder in-line two-stroke cycle Diesel engine, the cylinders are pitched 150 mm apart. The crank length is 100 mm and the ratio of connecting rod to crank is 4.5. The reciprocating mass per line is 1 kg. The engine speed is 2121 rpm. Two possible firing order for this engine are 1-5-3-6-2-4 and 1-4-5-2-3-6. As a young engineer, you have been tasked to evaluate the most suitable firing order for this engine. Your evaluation should include examination of the engine for balance of primary and secondary forces and couples for the given firing order. Apart from examining the engine, you need to justify why one firing order is superior to the other.
A flywheel absorbs 2500 ft-lb of energy at a coefficient of fluctuation of 0.10. The mean diameter of the flywheel is 72 inches. The weight of the arms and hub is 12 % of the rim weight. The mean rim speed is 80 fps. Consider the specific weight of the flywheel as γ = 0.26 lb/in3. A. Find the mean rpm of the rim. B. Determine the weight of the rim. C. What is the cross sectional area of the rim?
1. A three cylinder single acting engine has its cranks set equally at 120° and it runs at 800 r.p.m. Thetorque-crank angle diagram for each cycle is a triangle for the power stroke with a maximum torque of 100N-m at 60° from dead centre of corresponding crank. The torque on the return stroke is sensibly zero.Determine: 1. power developed. 2. Coefficient of fluctuation of speed, if the mass of the flywheel is 15 kgand has a radius of gyration of 70 mm, 3. Coefficient of fluctuation of energy, and 4. Maximum angularacceleration of the flywheel.
Problem Solving. Solve the following problems completely. 5. Motors from two different manufacturers are being considered for application.Both motors are 50Hp, 460 volts, 3 phase, 60 cycles. Motor A operates at 80%efficiency and motor B operates at 89% efficiency. The expected need for themotor is 15 years. Motor A cost P120, 000.00 and motor B P150, 000.00.Electrical energy cost P8.00 per Kw-Hr and the motors will be operating 8 hoursper day, 250 days a year. Assume taxes and insurance are 3% of first cost. Whichmotor should be purchased?
An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 200 kg at the crank pin, and the reciprocating masses per cylinder to 300 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the value of variation in tractive effort at 300 rpm. Select one: A. ±58476 N B. ±69780 N C. ±79654 N D. ±12475 N
Machine Theory Question-1 a) A flywheel is attached to the engine so that the rotational speed of the engine remains between 100 and 110 r/s. If the energy fluctuation is 1.05 KJ here, find the inertia of the flywheel.
The following data refer to a 12-cylinder, single-acting, two-stroke marine diesel engine:Speed: 150 rpmCylinder diameter: 0.8mStroke of piston: 1.2 mArea of indicator diagram: 5.5x 10-4 m2Length of diagram: 0.06 mSpring value: 147 MPa per mFind the net rate of work transfer from the gas to the piston in kW.
An engine develops 200 kW of power at a mean speed of 75 rpm. The coefficient of energy fluctuation is 0.15 and speed fluctuates within ±3% of the mean speed. Find the moment of inertia of the flywheel that must attached to the crankshaft of the engine in order to maintain the speedwithin the acceptable range.
20. A regenerative braking system stores kinetic energy of a car so that it can be recovered when the vehicle resumes moving. One way to do this is to “store” the energy in a spinning flywheel. One such design uses a solid disk flywheel with moment of inertia 0.040 kg m2 and maximum rotation rate 45000 rpm. (a) What is the maximum energy storage? (b) In principle it could store the kinetic energy of a 1700 kg car moving at what speed before braking? (c) If this energy is used to start the car moving again in 10.0 s, what is the power output of the system?
A punching machine requires 1600 ft-lb of energy to punch a certain hole. During the punching operation, the speed of the machine is reduced from 180 rpm to 160 rpm. The weight of the arms and hub is considered to be 10 % of the rim weight, and the mean diameter of the flywheel is 32 inches. a) What is the mean or operating rpm of the flywheel? b) Find the coefficient of fluctuation. c) What is the maximum speed of the flywheel, in fps? d) What is the minimum speed of the rim, in fps? d) Determine the weight of the rim, in lb. e) What is the weight of the flywheel, in lb? f) Determine the weight of the arms and hub, in lb.
7The total sleeve movement in a Hartnell governor is 3 cm. The mass of rotating balls is 1.5 kg each. At the mid position of the sleeve arm, which is 6.5 cm long, is horizontal. The ball arm has a length of 7.5 cm. At the mid position of the sleeve, the balls rotate at a radius of 10.5 cm. Due to the mal adjustment of spring, the equilibrium speed of governor at top position is 415 rpm and In lowest position it is 430 rpm. Determine (1) Stiffness and initial compression of spring. (ii) Required initial compression in spring which gives equilibrium speed at the topmost position which is rpm more than the lowest position neglect bliquity.m = 1.5 kg