A thin cylinder 80 mm internal diameter, 250 mm long with walls 2.5 mm thick is subjected to an internal pressure of 8MN/m². Determine the change in internal diameter and the What change in length. If, in addition to the internal pressure, the cylinder is subjected to a torque of 200 Nm, find the magnitude and nature of the principal stresses set up in the cylinder. E = 200 GN/m². v = 0.3.

A thin cylinder 80 mm internal diameter, 250 mm long with walls 2.5 mm thick is subjected to an internal pressure of 8MN/m². Determine the change in internal diameter and the What change in length. If, in addition to the internal pressure, the cylinder is subjected to a torque of 200 Nm, find the magnitude and nature of the principal stresses set up in the cylinder. E = 200 GN/m². v = 0.3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical tank of radius 50cm and wall thickness 4.0 mm is subjected to internal pressure of 2.0 MPa, and a torque of 0.0000005 Nm. Determine the maximum normal in the cylindrical container. Express your answer in MPa.
A 12cm x 16cm air compressor is operated with a maximum pressure of 10 kg/cm2. There are5 bolts with a yield value of 64ksi holding the cylinder head to the compressor. Determine the tensile stress of the bolt.
A cylinder which can be considered as a thin-walled shell, is made of steel plate 16 mm thick and is 2.14 m internal diameter. The cylinder is subjected to an internal fluid pressure of 0.55 MN/m2 gauge and, at the same time rotated about its longitudinal axis at 3000 rev/min. Determine:(a) the hoop stress induced in the wall of the cylinder due to rotation:(b) the hoop stress induced in the wall of the cylinder due to the internal pressure:(c) the factor of safety based on an ultimate stress of the material in simple tension of 456 MN/m2. Steel has a density of 7.8 Mg/m3.
A cylindrical pressure vessel has an inner diameter of 1.2 m and a thickness of 12mm. Determine the maximum internal pressure it can sustain so that neither itscircumferential nor its longitudinal stress component exceeds 140 MPa. Under thesame conditions, what is the maximum internal pressure that a spherical vessel with a similar inner diameter can sustain?
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
A 27 m vertical column of fluid (density 1878 kg.m3) is located where g= 9.65 m/sec2. Find the pressure at the base of the column.Ans. 489.313 kPa Please give me the solution.
The gas tank consists of a cylindrical section with two hemispherical endcaps. The cylinder has a diameter of 75 cm and a wall thickness of 2 cm. If the allowable circumferential stress is 150 MPa and longitudinal stress is 100 MPa, find the maximum allowable internal pressure in the tank. Answer: P = ___________________
An axial pull of 40000 N is acting on a bar consisting of three sections of length 30 cm, 25 cm and 20 cm and of diameters 2 cm, 4 cm and 5 cm respectively. If the Young’s modulus = 2 × 105 N/mm2, determine : (i) stress in each section and (ii) total extension of the bar.
SS 304 steel shaft is 3 m long and has an outer diameter of60 mm. When it is rotating at 60 rad/s, it transmits 30 kWof power from the engine to the generator. Determine thefollowing: a. The smallest thickness of the shaft if the allowableshear stress is 150 MPa and the shaft is restricted notto twist more than 0.08 rad. Use G for steel = 83 GPa. b. The percentage savings in weight had the generatorutilized a solid shaft. Assume same material, length andtorque capacity.
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
As the electric motor rotates at a constant speed, a torque of 500nm is applied to the ABCD shaft. When G = 27 GPa and the torques shown in the figure are applied to the B and C pulleys, what is B and C torsion.
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.