Answered: A thin cylinder of inner radius 500mm…

A thin cylinder of inner radius 500mm and thickness 10mm is subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: polypropylene PP rod attached ceiling 200 mm tick 25 mm width,3 mm length in loaded with 30 kg . fin...

A: Given data Thickness of Polypropylene rod = 200 mm Width = 25 mm Length = 3 mm Load = 30 kg Time = 2...

Q: A horseshoe player releases the horseshoe at A with an initial speed vo = 37 ft/sec. Determine the r...

Q: "). A drawing operation is used to form a cylindrical cup with inside diameter = 75 mm, height = 55 ...

Q: A cylinder witha 4-inch bore and 30-inch stroke extends in 7 seconds and moves a 25000 lb load, (a) ...

Q: the jet ratio is approximately 12. Find the size of the jet, mean diameter of runner, synchronous sp...

Q: ulate (a)the acceleration of the masses (b) the tension in the string.

A: Here we need to find acceleration of masses and tension in the string.

Q: Magnetic tape is being transferred from reel A to reel B and passes around idler pulleys Cand D. At ...

A: Write the given data in the problem. an1=32 m/s2 at2=40 m/s2 Here, an1 is the normal acceleration of...

Q: An open tank consists of 3 immiscible liquids, in which the water is at the height of 450 cm, above ...

A: GIVEN DATA- A TANK GIVEN FILLED WITH DIFFERENT FLUID WE HAVE TO FIND PRESSURE AT DIFFERENT LEVEL

Q: The line segment joining A(4, 1) and B(-2,5) is extended to point C through B. Find the coordinates ...

A: Given points are A(4,1) B(-2,5) The line AB is extended through B so that B becomes the midpoint o...

Q: A cylinder suspended by a rope rests against an inclined surface as shown. If the cylinder weighs 18...

Q: A hollow circular plate of 2 m external and 1 m internal diameter is immersed vertically in water s...

Q: A cylindrical tank subjected to internal pressurep is simultaneously compressed by an axial forceF =...

A: A cylindrical vessel or shell may be thin or thick depending upon the thickness of the plate in rela...

Q: An oil radiator has an outside surface area of 0.18 m2 and operates at a surface temperature of 85 d...

Q: A 4.0 kg mass, ml, hangs from a rope that runs over a massless frictionless pulley and is connected ...

Q: The capillary effect of water in mm is equal to=, The capillary effect of mercury in mm is equal to=

Q: istance of 100 m. Determine: ) the coefficient of kinetic friction between the tires and the road. ?...

A: QUESTION A)

Q: the nord stream 2 is a pipeline network from used to pump and transport Russian oil to germany. 2928...

A: Given: volume of oil trasported in one minute=29286 gallons=0.1605×29286=4700.40 ft3 so volume flow ...

Q: Elaborate the benefits of smart factory. Explain any one example wherein implementation of smart fac...

A: Smart Factory : The Smart Factory concept related to the various applications of different combinati...

Q: In a Carnot heat pump with R-134a as the working fluid, heat is rejected from the R-134a at 35°C and...

A: (a) Draw the T-s diagram for the Carnot heat pump. Here, 1 is the state of refrigerant before compr...

Q: An incompressible fluid flows through a pipe of length L = 1.00 m and conical section, which connect...

Q: 3. Complete the following table for water: T(C) P (kPa) 200 200 h (kJ/kg) Phase description| 0.7 Sat...

A: Given

Q: A car is traveling around a circular track of 760-ft radius. If the magnitude of its total accelerat...

Q: VA = 30 m/s 4. The pitching machine is adjusted so that the baseball is launched with a speed of VA ...

Q: 60% water vapor by volume. The liquid-vapor mixture is in equilibrium at 150°C. What is the quality ...

Q: Your steam has a Data of 5.32 MPa and 325 ℃. Find v, u, h and s.

Q: A carnot engine is working between the temperature range of 227°C and 127°C. If the heat absorbed by...

A: As given in question, Higher temperature in carnot cycle = TH = 227 oC = 500 K Lower temperature in ...

Q: Q.9/ The position of the particle is given by s = (2t 2 - 8t + 6) m, where t is in seconds. Determin...

A: GIVEN DATA - A DISPLACEMENT EQUATION IS GIVEN S=(2t^2-8t+6)m WE HAVE TO FIND TIME WHEN VELOCITY BECO...

Q: Q3: Explane in which case Fg has a maximum Value & minimum Value in Pulling the car shown in Fig 20 ...

A: According to the details provided in the question, we need to calculate Fb max or mini

Q: Determine the Miller Index of the given direction in an HCP crystal? Write the negative sign if the ...

Q: Given are 4 points in space: (x,y,x) A(3,2,3) B(0,1,4) C(2,4,1) D(0,5,4) The line of action of f...

Q: In a Rankine cycle, steam leaves the boiler and enters the turbine at 4 MPa and 400◦C. The condenser...

Q: An automobile starting from rest speeds up to 12 m/s with a constant acceleration of 1.2 m/s2. Runs ...

A: GivenV1=0 m/sV2=12m/sa=1.2m/s2V3=12m/sV4=0m/sa=-1.5m/s2d=390m

Q: (S) Sonic wave of air kg) "M2s 413 = o Z (to a longer liquid KG (M3 950) and quickly sound) 's cm 75...

A: Given DataZair=413 kgm2/sρL=950kgm3VL=750m/s

Q: Mr. Jae Yeong wants to put up a plant rack for his mini garden using a recyclable material from neig...

Q: Q.2/ The force exerted by the plunger of cylinder AB on the door is 40 N directed along the line AB,...

A: θ=tan-1 (100400)=14°FAB=40NM0=FAB (Cos 14 x 75 +FAB Sin 14 x 400)M0=FAB (Cos 14 x 75 +Sin 14 x 400...

Q: Figure Q1 shows the stress strain curves of six (6) samples. SIx 12 80 70 10 60 В * 50 40 D 30 20 E ...

Q: 10A plate 0.05mm distant from a fixed plate moves at 1.25 m/s and required a force per unit area of ...

A: GIVEN DATA- 1(a) SHEAR STRESS =2.2N/m2 , U=1.25 m/s , y=0.05mm , Specific gravity of oil =0.7 1(b) V...

Q: A bus at rest starts moving with an acceleration of 0.1 m/s² . What will be its speed after 2 minute...

A: Given, Initial velocity of bus = u = 0 m/s (As bus starts from rest) Acceleration of bus = a = 0.1 m...

Q: thapter 2, Problem 2/088 n exhaust system for a pickup truck is shown in the figure. The weights Wh,...

Q: In a reheat-regenerative Rankine cycle, the condenser pressure is 10 KPa. Steam enters the first tur...

Q: A creep experiment was performed on the mesenchymal cell with a 4.5 N force. Knowing that cellular m...

A: Solution: Given Data: F=4.5 NKs=3500 N/mηD=658 N-s/mδ=3.5 mm

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength...

A: As given in question, Minimum force during a cycle = Fmin = 20 kN Maximum force during a cycle = Fma...

Q: Calculate the power dissipated in Rs, as shown in Fig. (1). R1-6n www R2-30 R3=6n R4-2 n E= 19.8 V R...

A: Given: voltage→V=19.8 v To find out the current supplied in the circuit, we have to find out the equ...

Q: The refrigerator has light bulb which uses 15 W of power and the refrigerator has a COP of 1.3, what...

A: Note - electricity Cost's unit consider in $ (since P is not defined) Givenligh bulb power Q=15W =...

Q: 3.6 The force system acting on the machine part is equivalent to the single force R- 80i + 20j lb ac...

A: Force is an external agent capable of changing the state of rest or motion of a particular object of...

Q: Q.10/ The water nozzle ejects water at a speed 50 m/s at the angle 50° Determine the time where the ...

Q: 9) A raft is constructed of wood having a density of 600 kg/m. Its surface area is 5.7 m2, and its v...

A: Givendensity of the wood ρw=600 kg/m3surface area A=5.7m2volume V=0.6m3

Q: How many seconds in total willl it take for a 1.5-inch diameter cylinder with a 1-inch diameter rod ...

Q: Calculate the shape factor j for the wide-flange beam shown in the figure if h = 12.2 in., b = 8....

A: Given Data The height of the beam is: h=12.2 in The width of the beam is: b=8.08 in The flange thic...

Q: A bus at rest starts moving with an acceleration of 0.1 m/s² . What will be its speed after 2 minute...

A: From the given data, Initial velocity of bus = u = 0 m/s (As bus starts from rest) Acceleration of b...

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A thin cylinder of inner radius 500mm and thickness 10mm is subjected to an internal pressure of 5 MPa. The average
circumferential (hoop) stress in MPa is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.