A thin-walled closed cylinder (radius r of 400 mm; wall thickness t of 20 mm), is simultaneously subjected to an internal pressure p of 1.2 MPa, an axial force F (in tension or in compression) and at a torque T of 100 kN*m. Specify for the following two cases, and considering an FS of 2.8, the minimum uniaxial flow stress of the material so that plastic deformations in the cylinder are avoided. a) F = 160 kN in tension b) F = 800 kN in compression

A thin-walled closed cylinder (radius r of 400 mm; wall thickness t of 20 mm), is simultaneously subjected to an internal pressure p of 1.2 MPa, an axial force F (in tension or in compression) and at a torque T of 100 kN*m. Specify for the following two cases, and considering an FS of 2.8, the minimum uniaxial flow stress of the material so that plastic deformations in the cylinder are avoided. a) F = 160 kN in tension b) F = 800 kN in compression

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A polycrystalline metal has a plastic stress--strain curve that obeys Hollomon’s equation,σ = K εnDetermine n, knowing that the flow stresses of this material at 2% and 10%plastic deformation (offset) are equal to 175 and 185 MPa, respectively.
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
The rotation in degrees of a shaft, 800 mm long subjected to atorque of 80 N-m, 10 mm in radius and shear modulus of 85 GPais
The strength coefficient and strain-hardening exponent of a certain test metal are 750 MPa and 0.25, respectively. A cylindrical specimen of the metal with starting diameter = 75 mm is stretched. If the average flow stress on the part is 450 MPa determine the final diameter of the specimen.
A wire in the wire drawing machine, at the entrance entranceIt will be drawn from a drawer with 15 ̊. of the wireinlet diameter (D0) 2.5 mm and outlet diameter (Df) 2.0 mmdirection. Die and wire surface transitionswindow (μ) is 0.07. Wire strength (K)It is 205 MPa and the strain hardening superposition (n) is 0.20.Pre-section of wire (A0) 4.91 mm2and sector section area (Af) 3.14 mm2direction.Accordingly, wire drawing is done;a) Regression,b) Calculate the pulling force
A pressure difference of 35 pa is available to force -10c air. through a circular sheet metalduct 400 mm in diameter and 20m long. Find thevelocity in m/s. A.11.64 B.38.20 C.12.81 D.20.60 SHOW DETAILED SOLUTIONS
Calculate the rolling force required to hot reduce an AISI 1018 steel plate, 80 cm wide, from an initial thickness of 5 mm to a final thickness of 3.5 mm. The rollers are made of steel with a diameter of 350 mm. Through plane strain compression tests, it was determined that the material has a plane strain yield stress of 150 MPa. Assume an efficiency of 60%. Answer: P=3.24 NM
A horizontal shaft of 75 mm diameter projects from a bearing, and in addition to the torque transmitted the shaft carries a vertical load of 8 kN at 300 mm from the bearing. If the safe stress for the material, as determined in a simple tension test, is 135 MN/m2, find the safe torque to which the shaft may be subjected using as the criterion (a) the maximum shearing stress, (b) the maximum strain energy per unit volume. Poisson’s ratio v = 0.29.[Ans: 5.05, 8.3 kN.m]
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. a. At the MOST CRITICAL POINT of the sheet metal, calculate the stress state and sketch thecorresponding stress element b. If SAFETY FACTOR = 2 is considered, what is the MINIMUM shear force, V required tocut the sheet metal according to following criterions? i. ii. Tresca criterion?von Mises criterion? c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10^-6), respectively. A) What is the Poisson's Ratio of this material and it's Elastic Modulus? B) In a uniaxial test, the pipe's material is observed to yield at a longitudinal strain of 0.1 in/in. Assuming a factor of safety of 2, the pipe can withstand impact energy of _______ lb - in per foot without suffering permanent deformation. C) If the pipe is depressurized and then subjected to a torque of 50 lblb - ft.ft., it will experience a shear strain of ________ rad.
A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10^-6), respectively. A) What is the Poisson's Ratio of this material and it's Elastic Modulus? B) In a uniaxial test, the pipe's material is observed to yield at a longitudinal strain of 0.1 in/in.in/in. Assuming a factor of safety of 2, the pipe can withstand impact energy of _______ lblb - in.in. per foot without suffering permanent deformation. C) If the pipe is depressurized and then subjected to a torque of 50 lblb - ft.ft., it will experience a shear strain of ________ rad.
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. (Need answer Question c) & d) c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.