In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the ringsat A and B, respectively. If s = 0 when the cylinders are removed, determine the following:a. the horizontal distance x (mm) moved by point B/b. the mass (kg) of the two cylinders ,c. the forces (N) in the two springs,.d. the tension (N) in cable ABe.2 material. The Mate1 m2 mThi our1.5 mmay be subject to copyright ipepertyo dowwwnt to Part IV: The Law on Copyright1.5sworks that are subject to copyrightnd the copyright owners have the cNote: Use 9.81m/s? for theicatey be s.constant and kap=134 N/m.Parameterand ommunes = 0.8 + 0.0003*345 0.9035 ms = 0.8 + 0.0003*XYZ m[2|0|2|1||1| 3|6|2|1Example Student Number (SN)mww

At the point when a mass is hung upward from a spring, the spring extends. The power on the mass…

at A and B, respectively. If s = 0 when the cylinders are removed, determine the following: In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the rings c. the forces (N) in the two springs d. the tension (N) in cable AB e. the spring a. the horizontal distance x (mm) moved by point B/ b. the mass (kg) of the two cylinders, F of Unive 2 m 1m his material. The Materi 2 m Th aur 1.5 m Pspperty so do ww nt to Part IV: The Law on Copyrigh 1.5s works that are subject to copyright nd the copyright owners have the Note: Use 9.81m/s? for the p Kof the Philipal Cs=0.8 + 0.0003*345 = 0.9035 m constant and kBD=134 N/m. Example Student Number (SN) Parameter [2|0[2|1||1| 3|6|2|1| = 0.8 + 0.0003*XYZ m

at A and B, respectively. If s = 0 when the cylinders are removed, determine the following: In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the rings c. the forces (N) in the two springs d. the tension (N) in cable AB e. the spring a. the horizontal distance x (mm) moved by point B/ b. the mass (kg) of the two cylinders, F of Unive 2 m 1m his material. The Materi 2 m Th aur 1.5 m Pspperty so do ww nt to Part IV: The Law on Copyrigh 1.5s works that are subject to copyright nd the copyright owners have the Note: Use 9.81m/s? for the p Kof the Philipal Cs=0.8 + 0.0003345 = 0.9035 m constant and kBD=134 N/m. Example Student Number (SN) Parameter [2|0[2|1||1| 3|6|2|1| = 0.8 + 0.0003XYZ m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

The uniform ladder of weight W is raised slowly by applying a vertical force P to the rope at A. Show that P is independent of the angle .
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
What is the ratio L/R for which the uniform wire figure can be balanced in the position shown?
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The 20 × 20-in. square plate shown weighs 56 lb and is supported by three vertical wires. Determine the tension in each wire.
The homogeneous 40-kg basr ABC is held by a horizontal rope attached to end C. Neglecting friction, determine the tension in the rope.
The rectangular plate shown weighs 80 lb and is supported by three vertical wires. Determine the tension in each wire.
Determine the y-component of C (in kN, round-off to 2 decimal places) of the loaded frame. P=50kN and R=2m.
The crane BC shown below lifts a load of W. Neglecting the weight of the crane. Determine the following: a.) The Tension at Point A in terms of W. b.) The Reaction at Point B in terms of W.
A mechanism is used to apply a constant load Q to the seat in the manner illustrated. 1. Determine the following for the angle: - the lengths of LBE and LAB, in m - in degrees, the angles ? and ? 2. Compile the FBDs of members AB, FG, EBH, and GHI in their entirety. 3. Determine the forces involved in the following situations, in Newtons: - FG-member - H-pin - AB-cylinder hydraulic