A three-point bend test was performed on an alumina specimen having a circular cross section of radius 5.0 mm. If the specimen fractured at 3000 N, when the distance between the support points was 40 mm, calculate the modulus of rupture for alumina. Another test is to be performed on a specimen of the same batch alumina, but one that has a square cross section 15mm x 15mm Estimate the load at fracture if the support point separation is maintained at 40mm.

A three-point bend test was performed on an alumina specimen having a circular cross section of radius 5.0 mm. If the specimen fractured at 3000 N, when the distance between the support points was 40 mm, calculate the modulus of rupture for alumina. Another test is to be performed on a specimen of the same batch alumina, but one that has a square cross section 15mm x 15mm Estimate the load at fracture if the support point separation is maintained at 40mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Tensile test is a method to investigate the elasticity of a material. A test specimen is placed between two clamps and these clamps will move in opposite directions, hence straining the test specimen. This experiment will yield a stress-strain curve that shows each of the stages of the specimen for every load is applied. With an aid of sketching diagrams, describe the stages that the specimen experiences before it breaks, and relate it with the stress-strain curve. It is expected that each stage comes with a sketching of the specimen and explanation of the current stage.
Q: For a bronze alloy, the stress at which plastic deformation begins is 280 MPa, and the modulus of elasticity is 115 GPa. (a) What is the maximum load that may be applied to a specimen with a cross-sectional area of 325 mm? without plastic deformation? (b) If the original specimen length is 120 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 143 kN. - Length of the specimen is 29 mm. - The yield strength is 71 kN/mm2. - The percentage of elongation is 48 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1 mm at 18 kN and Final diameter if the percentage of reduction in area is 29 %. Initial Cross-sectional Area 2.01 mm2. The Diameter of the Specimen 1.59 mm. Final Length of the Specimen 42.92 mm. Stress at the elastic load 8955.22 N/mm2. Find: Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 143 kN. - Length of the specimen is 29 mm. - The yield strength is 71 kN/mm2. - The percentage of elongation is 48 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1 mm at 18 kN and Final diameter if the percentage of reduction in area is 29 %. FIND: Young's Modulus of the Specimen (in N/mm2) Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
In the First project: you have been asked to perform tensile testing for four different materialsand analyse the results and work on some NDT process selection:a. For the results shown in Table 1 of the tensile testing that you have performed, find thefollowing, if you know that the original length of specimen is 20.8 mm and the original diameteris 6.4 mm. Fill the calculated results in the summary table below (Table 1):1. Plot the engineering stress versus engineering strain for each material and L-D Diagram.2. Compute the modulus of elasticity, E in GPa.3. Determine the yield strength at a strain offset of 0.002.4. Determine the tensile strength in MPa.5. What is the approximate %El ductility, measured by percent elongation?6. Compute the modulus of resilience.7. Determine the fracture stress in MPa.8. Compute the final area (Af) in mm2.
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 157 kN. - Length of the specimen is 23 mm. - The yield strength is 89 kN/mm2. - The percentage of elongation is 45 %. Determine the following Diameter of the specimen, Final length of the specimen, Stress under an elastic load of 18 kN, Young's Modulus if the elongation is 1.3 mm at 18 kN and Final diameter if the percentage of reduction in area is 25 %. Fine this ans 1-Initial Cross-sectional Area (in mm2) 2-The Diameter of the Specimen (in mm) 3-Final Length of the Specimen (in mm) 4-Stress at the elastic load (in N/mm2) 5-Young's Modulus of the Specimen (in N/mm2) 6-Final Area of the Specimen at Fracture (in mm) 7-Final Diameter of the Specimen after Fracture (in mm)
Briefly comment on the values obtained for the Elastic Modulus, Yield Strength, Ultimate Strength and Toughness of the test specimen as compared to values of various comparable materials found in the literature. Is the test material comparatively strong? Is it stiff? Is it tough? Yield strength is 186Mpa, elastic modulus is 44.8GPa And the ultimate strength is 238.7mpa
2) For a brass alloy, the stress at which plastic deformation begins is345 Mpa and the modulus of elasticity is 103GPa.a) What is the maximum load that can be applied to a specimen with area130mm² cross section without plastic deformation? b) If the original length of the specimen is 76 mm, what is themaximum length to which it can be stretched without causing deformationplastic?
A three-point bending test is performed on a silicon carbide block that is 10 cm long, 1.5 cm wide, and 0.6 cm thick, and that is supported by two separate supports.7.5 cm. The sample breaks when a bending of 0.09 mm is recorded. The flexural modulus of silicon carbide is 480 GPa. Assume that no plastic deformation has occurred. Calculate: (a) The force that caused the fracture and(b) Flexural strength.
(Suppose you need to design a tension test machine capable of testing specimens that have nominal ultimate stresses as high as σu = 100 ksi . How much force must the machine be capable of generating? Assume the testing specimen has the ASTM shape shown. Answer for this is 19.6 kip) (If the maximum nominal strain is ϵf = 0.7 just before the test specimen fractures and the test machine operates by moving only one grip, how far must that grip be designed to travel? The total length of the deforming part of the specimen is 3 in. Answer for this is 2.10 in) Do not know if this info is needed but this was the other 2 parts
A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a Poisson's ratio of 0.35 is pulled in tension with a force of 40, 000 N. If the deformation is totally elastic and the original length is 120 mm, what is the final length of the specimen in mm?
Tensile test under 40,000 N load was applied to a low carbon steel with a sample diameter of 6 mm. As the diameter of the specimen under load decreases to 5 mm, calculate a) Engineering stress and% elongation values, b) Actual stress and% elongation values.