Q4A three strain gages have been attached directly to a piston used toraise a medical chair, the strain gages give strains as ɛa = 80 µ , Ep = 60 µandEc = 20 µ . Determine the principal strains and the principal straindirections for the given set of strains. And Compute the strain in a direction-30° (clockwise) with the x axis.a,x Ac.yPump

Answered: Image /qna-images/answer/7e22ffbc-611b-4070-beae-477bfeda187c.jpg

A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Ɛb = 60 µ 20 µ . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction Q4 %3D and Ec -30° (clockwise) with the x axis.

A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Ɛb = 60 µ 20 µ . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction Q4 %3D and Ec -30° (clockwise) with the x axis.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.3P: An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the...

See similar textbooks

Similar questions

During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
Three readings are obtained from an equiangular strain gage rosette mounted on a free and unloaded surface of a part. Determine the magnitude of the principal strains and their orientation with respect to the 0° gage. Check the results with a Mohr circle.Assume The three known strains are all linear strains
QB3 TWO DIMENTIONAL STRAINThree strain gauges were arranged in the form of a rectangular rosette and positioned on atest surface. The measured strains were as follows: 1 = 200x 10-6 2 = 100 x 10-6 3 = 50 x 10-6Determinea) the principal strains and the principle stressesb) the direction of the greater principal strain relative to gauge 1 and sketch the Mohrstrain circle. Take the Young Modulus of Elasticity value to be E = 200 GN/m2 andPoisson’s ratio  = 0.28.
Consider the given loading on a pipe. A rectangular rosette (45 degree apart) is placed on a point (K) which is located on the half length of the pipe as shown below. Note that the second gage (b) is parallel to the z-axis . When the load is applied, the strain gages read εa=80 µS, εb=60 µS, εc=20 µS. The pipe have an elastic modulus of Est=201 GPa. a. Determine the in-plane principal strains and the principal strain directions for the given set of strains (Use Mohr circle)
The strain rosette shown in Figures P13.28 only was used to obtain normal strain data at a point on the freesurface of a machine part.(a) Determine the strain components e x, e y, and γ xy at the point.(b) Determine the principal strains and the maximum in-planeshear strain at the point.(c) Draw a sketch showing the angle θp, the principal straindeformations, and the maximum in plane shear strain
A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
600 strain rosette, or delta rosette, consists of three electrical-resistance strain gagesarranged as shown in the figure. Gage A measures the normal strain e, in the directionof the x axis. Gages Band C measure the strains and e in the inclined directions shown.Obtain the equations for the strains 8. e. and y, associated with the x-v axes.
A 60º strain rosette, or delta rosette, is composed of three electrical resistance strain gauges arranged as shown in figure 5. Strain gauge A measures the normal strain εa in the x-axis direction. Strain gauges B and C measure the strains εb and εc in the indicated inclined directions. Using Mohr's Circle, obtain the equations for the strains εxx, εyy and γxy associated with the x and y axes.
Strain of Silly Putty: Initial length (L0): 2.85 cm Final length (L): 8.50 cm Strain: % (show calculation below): (Please type answer no write by hend)