A top is spun on the floor such that the top precesses around in a circular motion. The top has a mass of mand it's center of mass is located a distance of rem =0.1 kg0.03 m above the tip. The top is thrown with an angularvelocity of w =250 гad/s.a) Calculate the torque felt by the top if it leans an angle o.b) Find the direction of the torque felt on the top at the angle shown below.c) If the top precesses a full revolution in t =0.8 seconds, find the moment of inertia of the top.CM

Given; rcm=ll=0.03 mm=0.1 kgω=250 rad/s

A top is spun on the floor such that the top precesses around in a circular motion. The top has a mass of m = 0.1 kg and it's center of mass is located a distance of rem = 0.03 m above the tip. The top is thrown with an angular velocity of w = 250 rad/s. a) Calculate the torque felt by the top if it leans an angle ø. b) Find the direction of the torque felt on the top at the angle shown below. c) If the top precesses a full revolution in t = 0.8 seconds, find the moment of inertia of the top. 군 CM

A top is spun on the floor such that the top precesses around in a circular motion. The top has a mass of m = 0.1 kg and it's center of mass is located a distance of rem = 0.03 m above the tip. The top is thrown with an angular velocity of w = 250 rad/s. a) Calculate the torque felt by the top if it leans an angle ø. b) Find the direction of the torque felt on the top at the angle shown below. c) If the top precesses a full revolution in t = 0.8 seconds, find the moment of inertia of the top. 군 CM

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Turning moment 1mm = 60 Nm: crank angle, 1 mm = 1° . The turning moment shows the maximum energy that needs to be stored by the flywheel in the unit area is 2850 m² . The flywheel rotates at an average speed of 220 rpm with a total speed change of 2.5%. If the mass of the flywheel is 500 kg, find the appropriate dimensions (inner diameter, outer diameter and thickness) of the flywheel. Given that inner diameter of the flywheel is 0.9 outer diameter and the density is 7.2 Mg/m³ .
A wheel with rotational inertia 48 kg.m2 is mounted on a fixed, frictionless axle. The angular speed of the wheel is increased from zero to 59 rad/s in 12-s. What is the average net torque/Moment in N.m on the wheel during this time interval?
A rod has 14.0 kg of mass distributed uniformly over its length of 2.50 m and is suspended by two cords. Right after the rope is cut calculate the magnitude of the torque acting on it.
Consider a disc of mass, M with radius 0.5 m on a slope with angle 45 degrees to the horizontal. It has a good grip on the slope and does not slip. The disc is constructed so that its mass per unit area, ρ(r) = r1/2 kg m−2, with r being the radial distance in metres from the axis of the disc. What is the equation describing the linear acceleration of the centre of mass of the disc down the slope in terms of the angular acceleration of the disc.
A crane that is 10 meters long is rotating (while loaded), at 1 radians/sec. It is stopped instantly (in 0.1 radian) in the position shown. Due to momentum the load continues to swing. Ignoring the deflection of the crane for this problem. (list all assumptions). The load is 750 lbs. a) The weight of the 10 m crane boom is 3000 lb and the mass moment of inertia is 80 lb ft s^2 about the centroid. Using the parallel axis theory find the mass moment of inertia around the point of rotation. b) What forces and moments are there on the boom at the point of rotation?
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
A machine part has the shape of a solid uniform sphere of mass 220 gg and diameter 3.50 cmcm . It is spinning about a frictionless axle through its center, but at a point at the top of the sphere, it is scraping against metal, resulting in a friction force of 0.0200 NN at that point. Find the angular acceleration of the sphere, including the direction (a positive value would indicate the +z direction and a negative value would indicate the -z direction).
A flywheel has a mass of 250 kg, a radius of gyration 1.3 m and operating at 280 rev/min. The flywheel has an angular acceleration of 0.8 rad/s^2, it is initially at rest, find its final angular velocity and time taken to attained this velocity. Additionally, find the flywheel torque.
A circular solid disc of uniform thickness 20 mm, radius 200 mm and 20 kg, is used as a flywheel If it rotates at 600 rpm, what is the kinetic energy of the flywheel.
A flywheel maximum speed is 240 rpm and decrease to 200 rpm during the punching stroke. Themean diameter of the rim is 100 cm. Weight of the rim is 500 N and the weight of the arms andhub is 10% of the weight of the rim. Compute the energy released by the flywheel.
A wheel with rotational inertia 45 kg.m2 is mounted on a fixed, frictionless axle. The angular speed of the wheel is increased from zero to 44 rad/s in 13-s. What is the AVERAGE power input to the wheel during this time interval?
A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm. Find the length of the bar if it makes and angle of 45° with the vertical.