A torsional system consists of a mass moment of inertia disk of 30 kg.m? and a torsional damper with damping of 300 Nms/rad and a steel shaft (G=80Mpa) of 5 cm outer diameter, inner diameter of 2 cm and 1.5 m long. The shaft is crimped at one end and the disc is installed at the other. An angular oscillation of 4° amplitude is observed when a harmonic torque of magnitude of 2000 N.m is applied to the disk. Determine the maximum torque transmitted to the support in N.m.

A torsional system consists of a mass moment of inertia disk of 30 kg.m? and a torsional damper with damping of 300 Nms/rad and a steel shaft (G=80Mpa) of 5 cm outer diameter, inner diameter of 2 cm and 1.5 m long. The shaft is crimped at one end and the disc is installed at the other. An angular oscillation of 4° amplitude is observed when a harmonic torque of magnitude of 2000 N.m is applied to the disk. Determine the maximum torque transmitted to the support in N.m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A damped single degree of freedom mass–spring system has a mass m = 3 kg,a spring stiffness k = 2700 N/m, and a damping coefficient c = 18 N·s/m. Themass is subjected to a harmonic force which has an amplitude F0 = 20 N anda frequency ωf = 15 rad/s. The initial conditions are x0 = 4 cm, and x˙0 = 0.Determine the displacement, velocity, and acceleration of the mass after timet = 0.5 s.
An SDOF system consists of a mass with weight of 175 kg and a spring constant,k = 530kN/m. While testing the system a relative velocity of 30 cm/s was observed on application of aforce of 450 N. Determine the damping ratio, damped frequency of vibration, logarithmicdecrement, and the ratio of two consecutive amplitudes
Spring mass system has mass of 30 kg and natural frequency of .80 rad/s. Determine the stiffness of the spring.
A spring-mass-damper system oscillating about the horizontal surface is subjected to anexternal force of F = 300 sin (6)(t), where 300 is in Newtons and 6 is in radians per second. Thesystem has a mass 90 [kg], a damping coefficient of 78 [N ⋅ s/m] and a spring constant of300 [N⁄m]. The system is both given an initial displacement of 1.2 [m] and an initial velocity of 1.4[m⁄s].a. Using Method of Undetermined Coefficients, determine the particular solution for thedisplacement function.b. Determine the unknown coefficients for the homogeneous solution using the initialconditions (Note: the external force already works at t = 0).c. Determine the position, velocity, and acceleration of the system after 10 seconds.
1. Explain_why_the_natural_frequency_measurements_should_better_reflect_the_system’s_true_undamped natural_frequency_(and_therefore_correlate_better_with_calculated_values)_than_the_frequency_of_oscillation measurements. 2. For_a Linear Spring-Mass System, Torsional Spring-Mass System, and Simple Pendulum System: identify_the_necessary_measurements_required_to_identify_the_natural_frequency_and the damping_ratio_for_the_linear_SMD_and_the_simple_pendulum.
Between a solid mass of 10 kg and floor, two slab of isolator, natural rubber and feltare kept in series as shown in Figure Q1(b). The natural rubber slab has a stiffnessof 3000 N/m and an equivalent viscous damping coefficient of 110 Ns/m. The feltslab has a stiffness of 12,200 N/m and an equivalent viscous damping coefficient of170 Ns/m. (i) Sketch the single degree of freedom spring-mass-damper system(ii) Determine the undamped and damped natural frequencies of the system inthe vertical direction. Neglect the mass of the isolator
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
A shaft of 50 mm diameter and 0.5m long is fixed at one end and other end carries a disc of mass 500 kg. The radius of gyration of the disc is 0.5 m. Find the frequency of torsional vibration, if the modulus of rigidity for the shaft material is 80 GN/m2 .
A damped spring – mass system has a mass of 2 kg, a spring of stiffness 98 N/m and a dashpot with a viscous damping coefficient of 42 Ns/m. If the mass is disturbed by 70 mm and then released from rest, determine the displacement of the mass after 0·12 seconds
The measurements on a mechanical vibrating system show that it has a mass of 8 kg and that the springs can be combined to give an equivalent spring of stiffness 5.4 N/mm. If the vibrating system have a dashpot attached which exerts a force of 40 N when the mass has a velocity of 1 m/s, find : 1. critical damping coefficient, 2. damping factor, 3. logarithmic decrement, and 4. ratio of two consecutive amplitudes.
A machine is represented as a single degree of freedom spring-mass-damper system. The machine has a total mass of (100 + 16) kg, an out-of-balance mass 0.125 kg, eccentricity of 0.01 m, coefficient of damping (100 + 16) N/ (m/sec), and spring stiffness (1000 + 16) N/m. The rotational speed of the machine is3000 rpm. Determine the maximum amplitude of vibration due to out-of-balance. Suggest a method for the control of vibration caused due to out-of-balance
A four-cylinder automobile engine must be supported on three shock mounts,as shown in the picture. The engine block assembly weighs500 lbs. If the unbalanced force produced by the engine is given by200 sin 100 t lb, design three shock mounts (each stiffness k andviscous damping constant c) such that the vibration amplitudemaximum 0.1 in