Q2-A shaft of length 0.75 m, supported freely at the ends, is carrying a body of mass 90 kg at 0.25 m from one end. Assume E = 200 GN/m2 and shaft diameter = 50 mm. determine the following : 1- Circular frequency ( wn). 2- time period (t,) 3- natural frequency of transverse vibration (f.) 90kg -0.25m- -0.5m 0.75m

Q2-A shaft of length 0.75 m, supported freely at the ends, is carrying a body of mass 90 kg at 0.25 m from one end. Assume E = 200 GN/m2 and shaft diameter = 50 mm. determine the following : 1- Circular frequency ( wn). 2- time period (t,) 3- natural frequency of transverse vibration (f.) 90kg -0.25m- -0.5m 0.75m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.10P: The tensional pendulum shown in the figure consists of a horizontal circular disk of a mass M = 60...

See similar textbooks

Similar questions

A shaft 60 mm diameter and 4 m long is simply supported at both ends and carries three vertically downwards point-loads of magnitudes 900 N, 1000 N, and 850 N located at 1 m, 2 m, and 3 m from the left support, respectively. The Young's modulus for shaft material is 110 GN/m2. 3.1. Provide the diagram of the position of supports and loads on the shaft3.2. Calculate the natural frequency of transverse vibration of the shaft.
The crankshaft-flywheel assembly of a large engine may be considered a torsion pendulum. The shaft is 1.8m long and transmit 179.127kN-m torque corresponding to 83MPa stress. The flywheel diameter is 75cm and weighs 4.5kN. If the modulus of rigidity of the shaft material is 77GPa, compute the period of vibration of this system.
A cantilever shaft 50mm diameter and 300mm long has a disc of mass 100kg at its free end. The young’s modulus for the shaft material is 200GN/m2. Determine the frequency of longitudinal and transverse vibration of the shaft. (b)Explain the sketches different cases of damped vibrations.
A shaft of 50 mm diameter and 0.5m long is fixed at one end and other end carries a disc of mass 500 kg. The radius of gyration of the disc is 0.5 m. Find the frequency of torsional vibration, if the modulus of rigidity for the shaft material is 80 GN/m2 .
a hydraulic shaft carries a set of pulley wheels at the end. The motor has a moment of inertia of 0.8 kg.m^2. If the natural frequency of torsional vibration is 4.74 Hz, what is the distance between the motor and the pulley wheels in meter if the diameter of the shaft is 15mm and modulus of rigidity is 80 GN/m^2
A shaft 1.5 m long is supported in flexible bearings at the ends and carries two wheels each of 50 kg mass. One wheel is situated at the centre of the shaft and the other at a distance of 0.4 m from the centre towards right. The shaft is hollow of external diameter 75 mm and inner diameter 37.5 mm. The density of the shaft material is 8000 kg/m3. The Young’s modulus for the shaft material is 200 GN/m2. Find the frequency of transverse vibration.
An undamped spring/mass system, in which m = 8 slugs and the spring constant k = 16 lb/ft has a driving force f(t) = t^pi*t on [0,pi] Extend f(t) into the negative t-axis to obtain an odd function. Find the particular solution ??(?). (Note: f(t) is given as half of the period, p = π.)
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
In the undamped single storey sliding frame given in the figure, rectangular section columns are has. Column section dimensions are given in the table. E = 1.5x107 kN / m2 and g = 10m / s2 will be taken. (25P) a) Calculate the stiffness of each column. b) Calculate the natural vibration period and angular frequency of the system. k1=column1:40x40cmxcm k2=column2:30x30cmxcm k3=column3:35x35cmxcm w:238kN h:3.05m
A steel shaft of 0.05 m diameter and 2 m length is fixed at one end and carries at the other end a steel disc of 1 m diameter and 0.1 m thickness. Find a) the mass of the disc and its moment of inertia about the axis of the shaft, b) the stiffness of the steel shaft and c) the system’s natural frequency of torsional vibration.
A hollow shaft 3 feet long and with radii 1.5 in and 2 in is used to transmit power from an 8 HP motor to a drum of radius 2 fy (Modulus of rigidity= 11x10^6 ln/in^2). A cable wound on the drum supports a hoist. What angle is the shaft twisted when the hoist is pulled up with a constant speed of 2 in/s?
A disc shown at the picture below is mounted at the free end of a steel shaft 1.5 m in (7) length and 8 mm in the radius. The torsional elastic modulus of the shaft isG = 83x109 N/m2. The period of free torsional oscillations of the system is observed to be 2.3s Calculate:4.1.1. The second polar moment of inertia of the cross-section of the shaft 4.1.2. The mass moment of inertia of the wheel